-
zjx_RTC
stm32 野火开发板 rtc实例程序(stm32 rtc Example)
- 2014-07-21 20:45:55下载
- 积分：1
-
musicplayer
说明： 使用stm32f103读sd卡的文件系统中的音乐文件，并解析播放的程序。(STM32F103 is used to read the music files in the file system of SD card and parse the playing program.)
- 2020-06-21 10:20:01下载
- 积分：1
-
ALIENTEK-MINISTM32-
ALIENTEK MINISTM32 扩展实验21 ENC28J60网络模块实验(ALIENTEK MINISTM32 )
- 2015-12-31 22:09:20下载
- 积分：1
-
STM32f107-PLC
基于STM32F107处理器编写的一个完整项目程序，通过RS232的modbus协议通讯，实现远程控制此PLC开发板，实现节点检测，开关控制，实时状态的电压电流检测。(Based on the STM32F107 processor to write a complete project program, through the RS232 modbus protocol communication, to realize the remote control the PLC development board, realize node detection, switch control, real-time state of voltage current detection.
)
- 2020-12-21 15:29:10下载
- 积分：1
-
BOD-LPC1788
这是LPC1788掉电检测的程序,用于当由突发状况系统掉电时，紧急数据的保存，以免数据丢失。(This is the LPC1788 procedure of Brownout detection . In order to avoid data loss when power systems, emergency data is preservated.)
- 2020-06-29 03:00:02下载
- 积分：1
-
AVR230_source
This is a simple bootloader for AT91SAM7 processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.(This is a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.)
- 2009-11-17 10:47:55下载
- 积分：1
-
main
JXARM9-2410 数模转换实验主程序， 实现功能：，实现JXRAM9-2410与PC机的串口通讯，JXARM9-2410 UART0 <==> PC COM
(JXARM9-2410 digital-to-analog conversion experiments the main program, the realization of functions: to achieve JXRAM9-2410 and PC-Serial communication, JXARM9-2410 UART0 )
- 2008-07-10 18:04:52下载
- 积分：1
-
STM32PSI4463
基于STM32的SI4463的程序，分为收发两个部分，可变数据长度，可以设置发射功率，带RSSI(The SI4463 based STM32 program, divided into two parts transceivers, variable data length, you can set the transmit power, with RSSI)
- 2020-11-19 16:29:38下载
- 积分：1
-
SD卡读写模块
周立功公司为LPC213X ARM7 编写的SD卡读写模块，很详细的注释。(Zhou Ligong LPC213X ARM7 prepared for the SD card reader module, a very detailed notes.)
- 2020-06-26 09:00:01下载
- 积分：1
-
bootloader_Lite_v1.1
STM32 IAP启动程序
1,先将本程序通过jLink下载到目标板中。
2,现次上电前，先在超级终端中按下 C 键，然后上电，会显示操作菜单。
3,在按下‘1’后，进入到更新模式。
4,完毕后按下 2 运行程序。(STM32 IAP start the program, the first of the program by jLink download to the target board. 2, now times before the power, first in HyperTerminal, press ' C' key, then power will display the Actions menu. 3, press ' 1 ' , into the update mode. 4 is completed, press ' 2 ' to run the program.)
- 2013-05-17 15:28:40下载
- 积分：1
