网站首页

登录

fengji-pscad

于 2021-03-18 发布文件大小:1505KB

 0  289

下载积分: 1 下载次数: 213

我要下载

代码说明：

用PSCAD对文献中的永磁直驱风机模型进行了仿真，并且能够可靠运行。(PSCAD for literature with permanent magnet direct drive wind turbine models for simulation, and reliable operation.)

文件列表：

永磁同步风机仿真 pscad
......................\turb_gen_connection.emt
......................\.......................\EMTDC_gnu.log,0,2014-04-18
......................\.......................\Main.dta,1768,2014-04-18
......................\.......................\Main.f,10883,2014-04-18
......................\.......................\Main.o,7479,2014-04-18
......................\.......................\turb_gen_connection.exe,990235,2014-04-18
......................\.......................\turb_gen_connection.mak,3204,2014-04-18
......................\.......................\turb_gen_connection.map,3045,2014-04-18
......................\turb_gen_connection.psc,12031,2009-01-01
......................\Wind_turbine_PSCAD_V42_ref.pdf,1424563,2014-04-15

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

netdraw
社区发现最常用的画图工具netdraw 使用简单方便里面有使用说明及例子直接导入里面的例子文件即可(netdraw community detection)

2014-06-30 19:43:27下载

积分：1
Au_44nm_G1
石墨烯表面等离子体传感器曲线模拟程序！！！！！！(spr based on graphene)

2016-10-31 16:07:36下载

积分：1
TOLGC
说明：这个软件是用在CAD里的，给尺寸加公差上去很方便。(This software is used in the CAD in the, tolerances up to plus size is very convenient.)

2011-04-11 19:51:58下载

积分：1
the-image-tube-CAD
本文以电场的三大定理、连续超张弛迭代算法、拉格朗日插值算法等原理知识作为理论基础，以 C 语言为编程工具，将由根据以上物理和数学原理所推导出来的模型转化为可以计算像管内电势的 CAD 程序软件。所编写的程序可以在给定像管参数和电极电位的情况下，计算圆柱形像管内任意一点的电位大小，并绘制出像管内的等势线；拉格朗日插值得到对称轴上任一点的电位值。 (In this paper, we base on the three theorems of the electric field, continuous ultra-relaxation iterative algorithm, and Lagrange interpolation algorithm. We use the C language as a programming tools, and transform the model derived above into a CAD software to calculate the electric potential in the image tube. In case the image tube parameters and electrode potential are known, the program written can get the potential of every point in the image tube, and plot equipotential lines inside the image tube. It can also get the potential of every point on the axis of symmetry by Lagrange interpolation. )

2015-02-04 22:28:55下载

积分：1
PrintUtils_1
CadoDraw-Printutils for C++ Builder 6控件安装包(CadoDraw-Printutils for C++ Builder 6 installation package control)

2008-05-04 16:42:28下载

积分：1
DFA
说明：多重分形去趋势来分析处理生物医学信号，matlab程序代码(Multifractal detrended)

2020-06-21 15:40:02下载

积分：1
光强及相位
MATLAB仿真模拟了LG光束的光强及相位的3维图与2维图(MATLAB simulation of LG beam intensity and phase of the 3-dimensional diagram and 2-dimensional diagram)

2021-04-09 12:49:00下载

积分：1
jpaint-src-0.0.1
这是国外的同行编写的画图板程序，感觉比陈建春的要好些，说实话研究了半天，发现国内的cad水平低不是因为国内的人笨，主要是国外的cad技术不能很快的传递到国人手中，总是参考陈建华等水平有限，工程水平差的书籍造成整体水平低，书中没有详细的流程图，和软件设计思路，而且代码错误连篇。(This is the foreign counterparts of the drawing board to prepare procedures, CHEN Jian-chun than feeling the need to better tell the truth for a long time study and found that low levels of domestic cad because people are not stupid, mainly abroad cad technology should not quickly delivered to the the hands of the people always refer to Chen Jianhua, such as the limited level, engineering level difference caused by the overall level of books low, the lack of a detailed flow chart of the book, and software design, and code errors pack.)

2007-10-09 22:23:11下载

积分：1
bode
用m文件绘画伯德图，利用hold on命令可以绘画多个伯德图，然后进行频率响应对比。(plot Bode diagram by m file)

2018-04-03 17:42:30下载

积分：1
CHENGPIN
mfc绘图，用于绘制坐标系图形。动画的我的基本思路。(mfc draw)

2011-07-21 22:13:49下载

积分：1

696518资源总数
105877会员总数
14今日下载