-
Blindestimation
根据接收数据阵x 、信道长度LH、过采样因子q ，采用Hopfield 盲处理方法，恢复出相应于x的尽可能长的BPSK发送序列，并估计 信道。(Based on the received data matrix x, the channel length of the LH, oversampling factor q, with Hopfield blind treatment, recovery corresponding to x, send a sequence of BPSK as long as possible, and the channel estimate.)
- 2010-07-02 11:10:50下载
- 积分：1
-
ecg-signal
用matlab实现管道泄漏信号的仿真，并且有其他的突变信号，便于matlab仿真实验(Using matlab to achieve pipeline leak signal simulation, and there are other mutations in the signal, to facilitate the simulation matlab)
- 2011-09-09 10:16:32下载
- 积分：1
-
2-po-nFakt-deleno-nFaktP1-po-nFakt
program to see how is n equal to farenheit plus neshtosi tam
- 2014-09-16 02:01:14下载
- 积分：1
-
fuzzy-logic
La logique floue est le meilleur moyen de convertir les stratégies de contrô le du langage naturel qui sont utilisées par l’homme à une forme utilisable par les machines. Des expériences ont montré qu’un contrô leur classique donne parfois même de meilleurs résultats que l’opérateur humain
- 2013-12-08 18:04:19下载
- 积分：1
-
Staxen_Adaptive-Modulation
a power point tutorial demonstrate adaptive modulation
- 2014-03-16 14:09:39下载
- 积分：1
-
InputBuffer---
A buffer with 2 inputs and 2 outputs is implemented in this experiment.
The buffer has a buffer size k=6 cells for each input buffer, and arrival rate lambda, λ.
The Matlab software was used to make this buffer. Two 2*2 arrays were created as two for inputs and outputs, a 2*6 array is created as the body of buffer. This means the buffer can hold the 6 data from two sources and the buffer has two input ports and two outputs port.
However, it can only have one write or arrival for each input per slot time or cycle time and it can only have one read for each output per cycle time. We can only read out once per cell time from a given input buffer.(A buffer with 2 inputs and 2 outputs is implemented in this experiment.
The buffer has a buffer size k=6 cells for each input buffer, and arrival rate lambda, λ.
The Matlab software was used to make this buffer. Two 2*2 arrays were created as two for inputs and outputs, a 2*6 array is created as the body of buffer. This means the buffer can hold the 6 data from two sources and the buffer has two input ports and two outputs port.
However, it can only have one write or arrival for each input per slot time or cycle time and it can only have one read for each output per cycle time. We can only read out once per cell time from a given input buffer.
)
- 2012-10-16 18:25:40下载
- 积分：1
-
helloword
显示hello的matlab源代码
几句matlab的代码(Hello, matlab source code shows a few matlab code)
- 2011-04-20 21:37:09下载
- 积分：1
-
ls_AR
时间序列分析，采用了最小二乘（LS）与自回归(AR)的组合模型，并用MATLAB将其实现(Time series analysis, using a least-squares (LS) and autoregressive (AR) model combination and its implementation using MATLAB)
- 2013-09-10 11:13:58下载
- 积分：1
-
cicmpdem
Windows下的ICMP封装(Clcmp class which can echo)
- 2001-11-26 10:53:14下载
- 积分：1
-
widebanddoa
采用前后向平滑以及最小冗余线阵的宽带源DOA估计仿真(Used before and after smoothing, as well as to the minimum redundancy linear array of broadband source DOA estimate Simulation)
- 2007-09-17 14:54:07下载
- 积分：1
