-
fft
本文提出了一种采用六项余弦偶次幂窗三峰插值的算法来对电网谐波进行检测与分析。该算法通过分析电网信号加窗后傅里叶变换的频域表达式，利用谐波频点附近的三根离散频谱的幅值确定谐波谱线的准确位置，进而得到电网谐波的相关参数频率、幅值及相位的计算公式，最后再对其进行加权修正，从而进一步的提高检测的准确度和有效性。( this paper proposes an approach for power network harmonic detection and analysis based on six even order cosine window and triple-spectrum-line interpolation. Through analyzing the adding window signal fourier transform in the frequency domain expression, using amplitude of three discrete spectrum near the harmonic frequency point to determine the accurate position of the harmonic spectrum and get the calculation formula of related parameters of the power network harmonic such as frequency, amplitude and phase, the algorithm further enhances the accuracy and effectiveness by using weighted correction.)
- 2015-10-27 10:47:23下载
- 积分：1
-
arGJRsim.m
Simulation of an AR-GJR process
- 2012-03-28 01:49:57下载
- 积分：1
-
w
说明： 地震处理 叠后F-K偏移 有差值方法选择等(FK migration in the post-stack seismic processing)
- 2012-06-04 20:39:36下载
- 积分：1
-
Poisson
利用MATLAB写出 Poisson 概率给定到达率求出 Poisson 分布的机率质量函数(Use MATLAB to write the Poisson probability of a given arrival rate to calculate the Poisson distribution of the probability mass function)
- 2012-07-13 14:15:11下载
- 积分：1
-
(Proakis)-Digital-Signal-Processing-(Solution)
A Solution Manual for(Proakis)Digital Signal Processing (Solution)
- 2013-10-23 06:03:19下载
- 积分：1
-
stlwrite
matlab code for stlwrite - Write binary or ascii STL file
- 2015-02-07 13:45:16下载
- 积分：1
-
DFT-analysis-
利用DFT分析离散信号频谱的实验。利用FFT分析信号 x[k]=cos(3pik/8 +pi/4 ) 的频谱；确定DFT计算的参数，绘出其频谱；并进行理论值与计算值比较。(DFT analysis of discrete signal spectrum utilization experiments. Analysis using FFT signal x [k] = cos (3pik/8+ pi/4) of the spectrum determine the parameters of DFT calculations, draw its spectrum and comparing the theoretical and calculated values.)
- 2013-12-24 20:15:34下载
- 积分：1
-
matlab-introduction--book
matlab programing for engineers etc.
- 2015-04-05 12:50:45下载
- 积分：1
-
sydrome
syndrome calculater to reduce adaptive noise
- 2015-05-02 10:30:08下载
- 积分：1
-
motor_controller
包含了几个Matlab的示例仿真模型，用于展示如何控制一个直流DC电机。同时包含了一个文档教程，介绍不同控制器PID，和带有状态反馈的极点配置。可以作为你在Simulink中学习开发控制系统的入门教程。(Contains a few example of Matlab simulation model is used to demonstrate how to control a DC-DC motor. At the same time a document contains a tutorial to introduce a different controller PID, and with state feedback pole assignment. As you study the development of control systems in Simulink Tutorial.)
- 2012-06-08 16:20:47下载
- 积分：1
