-
ADC_PEC
英飞凌单片机使用pec中断的ad转换实例完整版(Infineon microcontroller interrupt the ad conversion using pec)
- 2021-03-25 13:59:14下载
- 积分:1
-
isight_code
isight与adams、MATLAB、adaqus等集成源程序(isight and adams, MATLAB, abaqus and other integrated source)
- 2016-07-10 11:00:59下载
- 积分:1
-
PLC--elevator
plc 的电梯控制程序,含有组态软件,控制算法。plc 采用三菱fx1n(plc elevator control program, containing configuration software)
- 2014-02-20 21:17:01下载
- 积分:1
-
33
模数转换ADC0832,基于51单片机的c语言程序(Analog to digital converter ADC0832, based on 51 MCU c language program)
- 2013-12-07 00:33:47下载
- 积分:1
-
CH911CI1
以8051为基础的有键盘;有液晶显示器;有传感器前置调理电路的数据采集器控制程序。(8051-based data acquisition control program)
- 2010-07-24 18:27:55下载
- 积分:1
-
VB--PIC
使用VB与PIC采集,采用软件中断方式,使用研华1710集成卡。(Using VB with PIC acquisition, the software interrupt, use the the Advantech 1710 integrated card.)
- 2012-09-30 00:27:14下载
- 积分:1
-
Exceptional-CPP
This second edition cancels and replaces the first edition,
ISO/IEC 9899:1990, as amended and corrected by
ISO/IEC 9899/COR1:1994, ISO/IEC 9899/AMD1:1995, and
ISO/IEC 9899/COR2:1996.
- 2014-10-22 21:17:02下载
- 积分:1
-
CodeWarrior
CodeWarrior仿真与调试要点,CodeWarrior仿真与调试要点,CodeWarrior仿真与调试要点(CodeWarrior simulation and debugging points, CodeWarrior simulation and debugging points, CodeWarrior point emulation and debugging)
- 2013-08-21 21:14:06下载
- 积分:1
-
SPI_STM32_FPGA
STM32F1与FPGA通过SPI进行通信,我上传的是32部分的程序,已经通过串口测试成功。此程序可拓展为和单片机,DSP通过SPI进行通信(STM32F1 and FPGA communication through the SPI, I uploaded the 32 part of the procedure has been successfully tested through the serial port. This program can be extended to and single-chip, DSP communication through the SPI)
- 2020-11-16 09:29:42下载
- 积分:1
-
Stepper-motor-drive-source
步进电机28BYJ48型四相八拍电机,电压为DC5V—DC12V。当对步进电机施加一系列连续不断的控制脉冲时,它可以连续不断地转动。每一个脉冲信号对应步进电机的某一相或两相绕组的通电状态改变一次,也就对应转子转过一定的角度(一个步距角)。当通电状态的改变完成一个循环时,转子转过一个齿距。四相步进电机可以在不同的通电方式下运行,常见的通电方式有单(单相绕组通电)四拍(A-B-C-D-A。。。),双(双相绕组通电)四拍(AB-BC-CD-DA-AB-。。。),八拍(A-AB-B-BC-C-CD-D-DA-A。。。)(Stepping Motor 28BYJ48 four-phase eight-phase motor, the voltage DC5V-DC12V. When a series of continuous control pulses are applied to the stepper motor, it can be continuously rotated. Each pulse signal corresponds to the stepper motor of a phase or two-phase winding power state change once, also corresponds to the rotor through a certain angle (a step angle). When the change in the power-on state completes one cycle, the rotor turns one pitch. Four-phase stepper motors can be operated in different power-up modes. The common power-up modes are: single-phase winding power (ABCDA ...), double (dual-phase winding)-DA-AB-...), eight beats (A-AB-B-BC-C-CD-)
- 2020-09-12 06:57:59下载
- 积分:1