登录
首页 » Unix_Linux » nuc900-linux-Ethernet

nuc900-linux-Ethernet

于 2014-05-19 发布 文件大小:9KB
0 147
下载积分: 1 下载次数: 3

代码说明:

  基于nuc900的读以太网程序源代码。可作为参考和移植。(Based on the nuc900 read Ethernet program source code. Can be used as reference and transplantation.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • msp430f6638_panio
    在CCS环境下用C写的TI的msp430f6638的一个电子琴程序,按不同的按键时,改变频率,蜂鸣器发出不同的声音,并且可实现按一个键播放一段乐曲。(In the CCS environment written in C TI s msp430f6638 an organ program, when you press a different key, change the frequency, the buzzer sounds different, and can be achieved by pressing a button to play a tune.)
    2020-12-28 20:39:02下载
    积分:1
  • humidity-monitoring-system
    远程仓库湿度监测系统,包含完整的程序开发文件,proteus仿真,keil文件,每步骤有注释(Remote warehouse humidity monitoring system)
    2016-09-12 07:49:09下载
    积分:1
  • CyUSBSerial_v3.0.11.0
    Zedboard上板载有一个USB转UART串口,采用了Cypress公司的USB-UART控制器CY7C64225。Zedboard的USB驱动安装很简单,首先下载USB驱动程序,解压缩后会有3个子目录分别对应Windows XP、Windows Vista和Windows 7系统,根据自己的计算机系统选择。(Onboard there Zedboard a USB-to-UART serial port, using Cypress' s USB-UART controller CY7C64225. Zedboard USB driver installation is very simple, first download the USB driver, unzip have three subdirectories corresponding to Windows XP, Windows Vista and Windows 7 systems, according to their own computer systems to choose from.)
    2014-07-14 19:13:19下载
    积分:1
  • 1.5Kw_PFC
    氮化镓实现的无桥FPC电路和设计资料,效率可以达到99.4 (Bridge-less FPC circuit and design information)
    2017-02-04 16:41:49下载
    积分:1
  • Proposed_Kumar_2015
    thesis on cognitive radio
    2016-07-30 17:09:57下载
    积分:1
  • NRF24L01
    NRF24L01按键测试程序可以通过按键来发送数据(NRF24L01 key test program)
    2014-02-24 18:50:34下载
    积分:1
  • E4PGX-CD-100127
    固高运动控制卡GE-400-PG随机光盘(GoogolTech GE-400-PG accompany CD)
    2020-09-11 08:18:01下载
    积分:1
  • wenduji
    12864 18B20做温度计 内含有仿真 是PROUUE 的仿真(12864 18B20 contains a thermometer to do simulation is the simulation PROUUE)
    2008-08-21 15:48:24下载
    积分:1
  • P1ExE
    P1口扩展实验 P1口既做输入口又做输出口,KEY1做为左转弯开关,KEY2做为右转弯开关。LED5、LED6做为左转弯灯,LED7、LED8做为右转弯灯(如图2-2)。 编程实现汽车转向灯功能,即:KEY1接高电平KEY2接低电平时,右转弯灯灭,左转弯灯以一定频率闪烁(注意:KEY拨向上方为0);KEY2接高电平KEY1接低电平时,左转弯灯灭,右转弯灯以一定频率闪烁;KEY1、KEY2同时接低电平时,发光二极管全灭;KEY1、KEY2同时接高电平时,发光二极管全亮。(P1 I extended not only to do experiments P1 I also do input output, KEY1 switch as a left turn, KEY2 as switches and turn right. LED5, LED6 as a left turn lights, LED7, LED8 as lights and turn right (Figure 2-2). Programming car turn signal function, namely: KEY1 high key2 access low-level access, the right turn lights out, left turn to a certain frequency of flashing lights (Note: KEY allocated to the top to 0) KEY2 access high Key1 low-level access, the left turn lights out, turn right to a certain frequency of flashing lights KEY1, KEY2 low at the same time, the light-emitting diode body KEY1, KEY2 high at the same time, the light-emitting diode light-wide.)
    2008-12-22 22:31:26下载
    积分:1
  • SD
    说明:  一个arm开发板的sd卡程序设计用于设计SD卡的实现(An arm development board designed sd card program is designed for the realization of SD card)
    2011-06-09 21:41:49下载
    积分:1
  • 696516资源总数
  • 106658会员总数
  • 16今日下载