登录
首页 » C++ Builder » c1

c1

于 2014-06-28 发布 文件大小:4KB
0 151
下载积分: 1 下载次数: 0

代码说明:

说明:  this is a C++ code to control a biomedical program you can use it

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Quectel_EC20_R2.0_TCP(IP)_AT_Commands_Manual
    移远4G通讯模块EC20AT指令手册可方便用户开发。(The EC20AT instruction manual for remote 4G communication module can be developed easily by users.)
    2018-07-25 11:13:15下载
    积分:1
  • SPI
    使用SPI接口读写EEPROM器件W25X16系统主时钟为12M,波特率为4M(Using the SPI interface to read and write EEPROM, main clock W25X16 system 12M, the baud rate is 4M)
    2011-07-19 12:36:10下载
    积分:1
  • AT24C02
    AT24C02串行E2PROM的工作原理与读写(AT24C02 E2PROM read & write)
    2011-05-24 18:17:14下载
    积分:1
  • Desktop
    电力仪表测量电压,电流,有功,无功,等电力参数,用PIC和ATT7026 数码显示(Electricity meters measure voltage, current, active power, reactive power, and other electrical parameters, with the PIC and ATT7026 digital display)
    2013-06-07 11:08:02下载
    积分:1
  • pwm
    说明:  使用msp430f5529产生pwm波的基本例程(Using msp430f5529 to generate PWM wave basic routine)
    2020-06-18 13:20:01下载
    积分:1
  • Frequency_Protocol_for_nRF24XX
    nrf24xx 2.4G无线鼠标跳频传输协议应用笔记,可用于无线鼠标,键盘等常见设备的灵活控制,采用跳频算法,避免其他信号源的干扰。(nrf24xx 2.4G wireless mouse hopping transport protocol, flexible control, to avoid interference with other signals.)
    2011-10-31 14:33:51下载
    积分:1
  • stc15f104e 控制DS18B20
    51单片机通过ds18b20对温度进行测量(temperature measurement)
    2018-08-21 12:19:17下载
    积分:1
  • mcp2515
    说明:  MCP2515 驱动,直接修改mcp2515.h里面端口即可移植使用。(MCP2515 driver, directly modify the inside ports of mcp2515.h can be transplanted.)
    2019-05-29 15:27:44下载
    积分:1
  • 2003-05-22_ps2kbd_fw
    说明:  一个PS2键盘单片机, 使用Philips的接口+8051,写的不错,非常值得学习.(a PS2 keyboard microcontroller, the use of the interface, Philips 8051, was a good, very worth learning.)
    2005-11-04 21:45:05下载
    积分:1
  • IO_SOFT_UART_USE_TIMER
    说明:   1. 本程序使用一个定时器和任意 2 个 I/O 口模拟一个串行口。 2. 1位起始位,8位数据位,1位停止位。发数据位时先发低位。 3. 支持半双工通讯。收、发波特率相同。 4. 应把定时器中断优先级设置为最高级。 5. 本程序每接收一个字节后就把它放到一个队列缓冲区中(也可使用环行缓冲区), 待缓冲区满后,将缓冲区中的内容原样发回。这是为了测试多字节连续收发的 能力和简化程序。实际应用中应防止缓冲区溢出。 6. 由接收转换到发送时要先调用 soft_send_enable (); 由发送转换到接收时要先调用 soft_receive_enable ()。 7. 发送最后一个字节后如果要立刻转为接收,必须等待最后一个字节后发送完毕 while ( rs_f_TI == 0) // 等待最后一个字节发送完毕(err)
    2008-09-16 13:37:34下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载