-
基于LabVIEW的通用自动测试系统设计
基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
real-time
根据倾角仪输出信号labview实时显示曲线图像的labview程序(Real-time display of curve image based on LabVIEW output signal of inclinometer)
- 2019-02-27 20:03:49下载
- 积分：1
-
PLC
说明： 利用LabVIEW和PLC通讯，相对其他软件更加简单(The use of LabVIEW and the PLC communications, compared with other software more simple)
- 2010-03-18 11:29:22下载
- 积分：1
-
TCP客户端程序
基于labview的TCP客户端程序发送主机通常将发送缓冲区中的数据按内存地址从低到?的顺序发出,接收主机把从?络上接到的字节依次保存在接收缓冲区中,也是按内存地址从低到?的顺序保存。
TCP/IP协议规定,?络数据流应采??端字节序,即低地址?字节。
socket API是?层抽象的?络编程接?,适?于各种底层?络协议,如IPv4、 IPv6,以及后?要讲的UNIX Domain Socket。(Based on the TCP client program to send the host LabVIEW will usually send buffer according to the data in the memory address from low to order issued, the receiving host to receive from the network bytes on sequentially stored in the receive buffer, and according to the memory address from low to preservation order.
The TCP/IP agreement, network data flow should be endian, low byte address.
Socket API is layer abstract network programming interface, suitable in various underlying network protocol, such as IPv4, IPv6, and UNIX Domain Socket to say.)
- 2018-01-15 01:19:31下载
- 积分：1
-
prog10
《Labview高级编程与虚拟仪器工程应用》第10章，关于液压系统测试的源码。包括：
1.“溢流阀动态”测试程序，其中小波变换使用了光盘中提供的VI,来自NI公司的高级信号处理工具包6.1版。“溢流阀动态.vi”是主程序。
2.“液压教学实验台”，“液压测试系统.vi”是主程序。
3.“机油泵”试验程序需要较多外部硬件支持。其中的dll用于国内某一特定品牌扭矩仪。“程序”文件夹的“main.vi”是主程序。
4.“转向泵”试验程序需要外部硬件支持。“程序”文件夹的“转向泵试验.vi”是主程序。(Labview high-level programming and virtual instrument engineering application)
- 2013-12-04 10:35:44下载
- 积分：1
-
通过串口采集下位机信息 smart
本程序是基于LABWINDOWS/CVI 的，主要是通过串口采集下位机信息，然后显示状态信息并通过串口发送命令字节。(The program is based on LABWINDOWS/CVI.It get message from RS232and display status,then send command by RS232.)
- 2011-11-28 21:08:44下载
- 积分：1
-
The-sound-tech-based-on-Labview
基于Labview的声音检测技术CAA文献，可鉴别人声，运用了Matlab小波分析。(Labview-based voice detection technology CAA literature, can identify the human voice, the use of Matlab wavelet analysis.)
- 2014-05-10 09:39:39下载
- 积分：1
-
NI VISAUSB
labview的一个usb和visa通讯的很好的一个参考例子(LabVIEW a USB and visa communication is a good example of reference)
- 2017-10-26 15:28:40下载
- 积分：1
-
kongtiaojiemian
空调的Labview的界面编程，界面显示从电机传出的数据，如电流、电压(Air conditioning of the Labview programming interface, interface display data coming from the motor, such as current voltage
)
- 2013-03-08 10:37:31下载
- 积分：1
-
qq
说明： labview 振动分析软件,该软件可通过声卡采集信号(LabVIEW vibration analysis software that can be collected through the sound signal)
- 2007-12-21 12:44:20下载
- 积分：1
