登录
首页 » matlab » nonlinear_c

nonlinear_c

于 2014-07-29 发布 文件大小:11KB
0 192
下载积分: 1 下载次数: 18

代码说明:

  非线性电容的matlab/simulink模型,实测可用!(Nonlinear capacitance matlab/simulink model, the measured available!)

文件列表:

nonlinear_c.mdl,56780,2014-05-22

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • enargie_soleil
    programme pour calcule sunrise sunset soleil
    2012-01-05 08:37:31下载
    积分:1
  • Kalman_estimation
    采用卡尔曼滤波法进行电池参数辨识,结果准确,辨识精度高(Identification of battery parameters by using Kalman filter method)
    2018-03-12 13:01:41下载
    积分:1
  • ttt
    让某一频率以下的信号分量通过,而对该频率以上的信号分量大大抑制的电容、电感与电阻等器件的组合装置。 (low-pass filter )
    2011-01-08 23:30:49下载
    积分:1
  • zaoshengguoxitong
    一个关于量化噪声分析的程序。代码不长仅供参考。学生试验专用。(One of the quantization noise analysis program. The code is not long for reference only. Students of special test.)
    2012-04-20 08:13:45下载
    积分:1
  • filter
    用MATLAB中的DSP BUILDER 设计的 FIR低通滤波器(Used in MATLAB DSP BUILDER design of FIR low-pass filter)
    2011-07-31 12:34:54下载
    积分:1
  • MATLAB-trans-Edge
    以MATLAB將影像做邊緣偵測以及邊緣強化, 邊緣偵測分別為Prewitt以及Canny, 邊緣強化是將邊緣做銳利化(MATLAB will do to the image edge detection and edge enhancement, edge detection, respectively Prewitt and Canny, edge enhancement is done to sharpen the edge)
    2013-08-28 23:18:05下载
    积分:1
  • PI_adjust
    说明:  单相并网逆变器,使用无源阻尼,实现并网电流波形和电网电压波形同频同相(Single-phase grid-connected inverters, using passive damping, realize grid-connected current waveform and grid voltage waveform in the same frequency and phase)
    2019-04-26 16:39:24下载
    积分:1
  • CH5
    This is a GUI based system. The GUI is invoked from the command line by typing "ui_start". The GUI is self explanatory. Tool tips are given in blue color. The cursor needs to be positioned on these for detailed explanation. The main file is "runsim.m".It is recommended that 10000 runs (packets) be used for plotting frame error rates and 5000 runs for BER/SER. Obviously, you would require a fast machine!!! At least a P4 machine. We have used trace criterion for 4PSK states 4,8 and 16 as an example for 2x2 cases. The reader can use rank and determinant criteria, by commenting the trace criterion lines and copying the rank and determinant lines from the respective 2x1 cases. The SNR range can be varied by correcting the range at line 36 of file "runsim.m". This software has been tested with MATLAB version 6.0 and above with signal processing and communications toolbox options. (This is a GUI based system. The GUI is invoked from the command line by typing " ui_start" . The GUI is self explanatory. Tool tips are given in blue color. The cursor needs to be positioned on these for detailed explanation. The main file is " runsim.m" . It is recommended that 10000 runs (packets) be used for plotting frame error rates and 5000 runs for BER/SER. Obviously, you would require a fast machine!!! At least a P4 machine. We have used trace criterion for 4PSK states 4,8 and 16 as an example for 2x2 cases. The reader can use rank and determinant criteria, by commenting the trace criterion lines and copying the rank and determinant lines from the respective 2x1 cases. The SNR range can be varied by correcting the range at line 36 of file " runsim.m" . This software has been tested with MATLAB version 6.0 and above with signal processing and communications toolbox options.)
    2011-05-04 09:22:01下载
    积分:1
  • Compar_fuzzy_pid
    fuzzy pid and pid with disturbance included
    2012-09-26 19:04:47下载
    积分:1
  • TE_run-example
    对gpr跨孔进行处理的程序,有助于地质专业的学生进行学习与研究。(the programe is for geometry students in sdutying end anlysis.)
    2012-04-12 18:56:48下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载