登录
首页 » Windows_Unix » CR

CR

于 2015-12-23 发布 文件大小:7KB
0 188
下载积分: 1 下载次数: 1

代码说明:

说明:  认知无线电频谱感知算法matlab程序,能量检测和匹配滤波,协作(cognitive radio ,spectrum sensing , energy detection )

文件列表:

matlab程序
..........\and.m,3021,2015-12-22
..........\andcompareor.m,1470,2015-12-22
..........\energy.asv,2066,2015-12-23
..........\energy.m,2066,2015-12-23
..........\or.m,3040,2015-12-22
..........\pipeilvbo.m,2043,2015-12-22

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • control_no_out_.ino
    利用温度控制制冷设备运行,实现空调扇自动制冷(Using temperature control refrigeration equipment to realize automatic refrigeration of air conditioning fan)
    2020-06-20 07:40:01下载
    积分:1
  • 130BCBF150BCBF
    说明:  步进电机的电子详细资料、对于了解步进电机3(For more information on the electronic stepper motor, stepper motor for about 3)
    2010-04-27 15:26:21下载
    积分:1
  • Advanced-C
    This is an advance C language book.
    2014-04-27 15:46:22下载
    积分:1
  • ADC_DMA
    说明:  使用stm32f103的adc功能采集电压数据,使用了DMA,12通道(Using the ADC function of STM32F103 to collect voltage data, using DMA, 12 channels)
    2019-12-05 09:29:57下载
    积分:1
  • 1390
    stm32f103读写ds1390时钟芯片程序(stm32f103ds1390 c aaaaa)
    2021-03-31 17:29:09下载
    积分:1
  • TEMP
    说明:  51单片机,ds18b20温湿度传感器,温湿度值通过LCD1602显示。(51 single chip computer, DS18B20 temperature and humidity sensor, temperature and humidity value through LCD1602 display.)
    2020-06-20 17:40:02下载
    积分:1
  • 基于STM32的电子秤
    电子称重的实现首先是通过压力传感器采集到被测物体的重量并将其转换成电压信号。输出电压信号通常很小,需要通过前级信号处理电路进行准确的线性放大。放大后的模拟电压信号经AD转换进入主控单片机中,再将结果显示在人机界面。(The realization of electronic weighing is firstly to collect the weight of the measured object through a pressure sensor and convert it into a voltage signal. The output voltage signal is usually very small, which requires accurate linear amplification through the front signal processing circuit. The amplified analog voltage signal is converted into the main MCU by AD, and the results are displayed in the man-machine interface.)
    2019-05-23 15:46:32下载
    积分:1
  • 密码锁及proteus仿真
    单片机上电以后LCD屏上显示欢迎回家, 先验证指纹再验证密码 ,同时验证成功开锁 指纹和密码分别可以验证3次 3次都错蜂鸣器响 ,按下manage键进入管理员模式 可以修改密码 删减指纹,指纹用开关量表示(After the microcontroller is powered on, the LCD screen shows welcome home. First verify the fingerprint and then verify the password. At the same time, verify the successful unlocking fingerprint and password can verify that the buzzer rings three times and three times respectively. Press the management key to enter the administrator mode to modify the password and delete the fingerprint. The fingerprint is expressed by the switch.)
    2019-06-21 14:12:41下载
    积分:1
  • ISD1790C
    ISD1790-C程序,用于ISD1790芯片开发的人进行参考。(ISD1790-C procedures for ISD1790 chips were developed by reference.)
    2008-12-25 16:47:19下载
    积分:1
  • VS2010CSharp-visual-scope
    上位机示波器驱动程序,VS2010 C#版本,对于做控制的同学十分有用(PC oscilloscopes driver, VS2010 c# version, classmates are very useful for do control )
    2014-01-18 20:14:04下载
    积分:1
  • 696518资源总数
  • 105885会员总数
  • 31今日下载