-
Fourth-order-LongGe-coulthard-method
本文件中，包含了微分方程的求解C++程序，以及绘制的函数图象(This document contains the differential equation C++ program, and the mapping function of image)
- 2011-11-09 09:07:10下载
- 积分：1
-
src
采用Sutherland-Hodeman多边形裁剪算法和Cohen-Sutherland直线裁减算法在java界面实现(The implementation of the Sutherland-Hodeman polygon clipping algorithm and the Cohen-Sutherland line reduction algorithm in the java interface)
- 2020-12-17 18:19:12下载
- 积分：1
-
六自由度机器人源程序
说明： 将Matlab与solidworks联合仿真，运用你运动学公式，求解六自由度并联机器人的工作空间(The workspace of a 6-DOF parallel robot is solved by using your kinematics formula and the joint simulation of MATLAB and solidworks.)
- 2021-04-28 14:28:43下载
- 积分：1
-
MyDrawTable
本程序用于绘制框架图，生成动态曲线，数据分析(Drawing frame diagram, generating dynamic curve, data analysis)
- 2017-12-21 12:14:33下载
- 积分：1
-
Motor-frequency-characteristics
在pscad中，双馈，同步，异步，电机频率特性的对比(Synchronous，Asynchronous，dfig ,Motor frequency characteristics of contrast in pscad)
- 2012-03-24 14:47:03下载
- 积分：1
-
Cadence-Allegro-Chinese-tutorial
Cadence Allegro 中文教程(Cadence Allegro Chinese tutorial)
- 2013-12-17 14:18:17下载
- 积分：1
-
LayoutFigure
The figure used to draw the feedback on a layout.
- 2014-05-09 15:17:58下载
- 积分：1
-
3phload
Three Phase load with Externally controlled Variable Source with PSCAD
- 2016-11-17 22:21:06下载
- 积分：1
-
jpaint-src-0.0.1
这是国外的同行编写的画图板程序，感觉比陈建春的要好些，说实话研究了半天，发现国内的cad水平低不是因为国内的人笨，主要是国外的cad技术不能很快的传递到国人手中，总是参考陈建华等水平有限，工程水平差的书籍造成整体水平低，书中没有详细的流程图，和软件设计思路，而且代码错误连篇。(This is the foreign counterparts of the drawing board to prepare procedures, CHEN Jian-chun than feeling the need to better tell the truth for a long time study and found that low levels of domestic cad because people are not stupid, mainly abroad cad technology should not quickly delivered to the the hands of the people always refer to Chen Jianhua, such as the limited level, engineering level difference caused by the overall level of books low, the lack of a detailed flow chart of the book, and software design, and code errors pack.)
- 2007-10-09 22:23:11下载
- 积分：1
-
the-image-tube-CAD
本文以电场的三大定理、连续超张弛迭代算法、拉格朗日插值算法等原理知识作为理论基础，以 C 语言为编程工具，将由根据以上物理和数学原理所推导出来的模型转化为可以计算像管内电势的 CAD 程序软件。所编写的程序可以在给定像管参数和电极电位的情况下，计算圆柱形像管内任意一点的电位大小，并绘制出像管内的等势线；拉格朗日插值得到对称轴上任一点的电位值。 (In this paper, we base on the three theorems of the electric field, continuous ultra-relaxation iterative algorithm, and Lagrange interpolation algorithm. We use the C language as a programming tools, and transform the model derived above into a CAD software to calculate the electric potential in the image tube. In case the image tube parameters and electrode potential are known, the program written can get the potential of every point in the image tube, and plot equipotential lines inside the image tube. It can also get the potential of every point on the axis of symmetry by Lagrange interpolation. )
- 2015-02-04 22:28:55下载
- 积分：1
