-
2011-5-4
51单片机编写的网络节点 自组织无线网络(51 single written self-organizing wireless network nodes network)
- 2011-07-04 18:55:50下载
- 积分：1
-
GEADVANCE3D_Sinogram
数据转换为正弦图，最终输出的正弦图为平均正弦图。(Data into sine figure, final output sine the graph is the average sinogram.)
- 2013-10-07 15:26:07下载
- 积分：1
-
msOS
MS5基于STM32F103设计开发，可以在Keil下软件仿真调试，不需要实物硬件板子，UART1作为人机窗口。硬件测试是基于正点原子的miniSTM32F103RBT6板子测试，资料是开源的。MS5主要基于MS4（基于NXP Cortex M3）升级而来，因为在2011年基于MS4做了6KW高频焊接机，增加了界面部分，采用函数指针加消息机制，感觉比较简单而有效，性能比较不错，尤其是针对工业产品，系统节拍分时设计有进一步的体会，把这两点融入到MS5中，同时修改了串口UART发送系统等待问题，先把串口数据放到一个buff中，系统节拍去检测buff，当有数据时，每个节拍发送一个，这样就避免了以前发送的时候，需要很长的等待问题。(MS5 based on the design and development of STM32F103 in Keil software simulation debugging, does not require physical hardware board UART1 as a man-machine window. The hardware test is based the the punctuality atoms miniSTM32F103RBT6 board test, and the information is open source. MS4 MS5 mainly based on (upgrades from NXP Cortex M3), because in 2011 based on the MS4 6KW high-frequency welding machine, increase the interface part of the function pointer plus message mechanism, feeling relatively simple and effective, and the performance is quite good, beats especially for industrial products, systems, time-sharing design further experience, these two points into the MS5 while waiting for problems to modify the serial UART transmit the first serial data into a buff system beats to detect buff, data, send each beat, thus avoiding the previously sent, the long wait.)
- 2013-03-18 13:04:42下载
- 积分：1
-
miehuo
灭火小车 机器人 。。。。 (use miehuo car)
- 2016-07-11 10:03:03下载
- 积分：1
-
IAP_64k_flash_最终版
STM32在线更新，代码测试完成，绝对可用。(STM32 online update, code testing completed, absolutely available.)
- 2020-06-16 23:40:01下载
- 积分：1
-
1286418B20
开关记忆和18B20在12864显视和读写24C20(Switch Memory and 18B20 were in the TV and read 24C20 12864)
- 2011-02-11 07:05:42下载
- 积分：1
-
MC9S08
飞思卡尔8位单片机MC9S08教程详解不带历程(Freescale 8-bit microcontroller MC9S08 Detailed tutorials)
- 2013-08-18 16:03:37下载
- 积分：1
-
28335_ECAN_1PROGRAM
参考ti提供得例子程序，先将他们得例子在自己得板子上跑起来，其实就是用自测试得方式来验证一下程序，也可以加些中断，看看程序怎么跑得。这步没问题得话，可以改写程序，当然还在自测试模式下先试，如果可以改写后，在自测试模式下可以。那么就差不多了，将自测试模式改成正常模式，将程序移植到自己得程序中，拿一个经过验证可以正常通讯得can模块通讯，记得两个can得速率要一致。当然这个can模块还要能让你看到或者说能验证你得can是否通讯正常。(Reference ti provide examples of procedures was, first they have to run up on the example of the board that she has, in fact, self-test was used to verify the program mode, you can also add some interruption to see how to run the program. This step was not a problem, you can rewrite the program, of course, still in test mode since the first try, if you can rewrite, can in self-test mode. Well almost, the self-test mode to normal mode, the program was ported to own program, get a proven module can communicate normally too can communicate, remember that two can get a rate to be consistent. Of course, this can also allow you to see the module or can verify whether you have can communicate properly.)
- 2014-07-10 20:13:37下载
- 积分：1
-
单片机程序调试黑宝书
说明： 单片机程序调试黑宝书，很好的书籍，适合入门。(Single-chip computer program debugging black book, a good book.)
- 2020-06-19 09:20:02下载
- 积分：1
-
STM32_EXTI
STM32单片机开发例程，这里是外部中断的开发例程(STM32 MCU development routines, here is the development of the external interrupt routine)
- 2014-04-13 16:48:03下载
- 积分：1
