-
feeback
MATLAB SIMULINK设计的电液伺服控制仿真系统(MATLAB SIMULINK simulation system designed electro-hydraulic servo control)
- 2010-11-19 11:25:31下载
- 积分：1
-
lbh
无线异构网络中继功率分配算法.AF协议的中继放大系数（中继将接收信号用一个因子量化，该因子与接收功率成反比）,利用QPSK调制解调，最后算出误码率
(matlab ber P)
- 2012-05-04 18:21:35下载
- 积分：1
-
GAs
遗传算法简明教程，附带程序，深入浅出讲解(Simple genetic algorithm tutorial, with procedures in layman' s language to explain)
- 2010-07-21 16:34:53下载
- 积分：1
-
MatlabRidgeDetection
Matlab多种图像边缘检测方法
1、用Prewitt算子检测图像的边缘
2、用不同σ值的LoG算子检测图像的边缘
3、用Canny算子检测图像的边缘
4、图像的阈值分割
5、用水线阈值法分割图像
6、对矩阵进行四叉树分解
7、将图像分为文字和非文字的两个类别
8、形态学梯度检测二值图像的边缘
9、形态学实例——从PCB图像中删除所有电流线，仅保留芯片对象(Matlab a variety of image edge detection method 1, using Prewitt operator edge detection image 2, with different values of σ LoG operator edge detection image 3, the detection operator Canny edge image 4, image segmentation threshold 5, water line image segmentation threshold 6, on the matrix quadtree decomposition of 7, the image is divided into text and non-text for these two types of 8, detection of morphological gradient of the edge binary image 9, morphological examples- from the PCB images to remove all current lines, retaining only the target chip)
- 2009-05-25 17:49:48下载
- 积分：1
-
qb
说明： 铅垂平面比利导引法弹道仿真程序，基于MATLAB编写(Vertical plane guidance law Billy ballistic simulation program, based on the MATLAB prepared)
- 2008-11-07 22:54:04下载
- 积分：1
-
zuiganfa
计算方法设计求解线性方程组的追赶法的matlab程序，是自己的计算方法作业，有详细的注解(Method designed for solving linear equations matlab program catch-up method, the calculation of their own work, with detailed comments)
- 2010-05-23 10:40:10下载
- 积分：1
-
fenshuweicalculation
A program that can easily caculate the fractal dimension. You need only input the parameter and then push the button.(A program that can easily caculate the frac tal dimension. You need only input the paramete r and then push the button.)
- 2007-03-21 15:24:52下载
- 积分：1
-
still
地球不转时的星下点轨迹，回归周期1天，可自行设定(Earth does not rotate when the nadir track one day return period)
- 2013-07-19 15:04:50下载
- 积分：1
-
line_inter_2d
Matlab的M文件编写的数控插补2D直线算法仿真。具体参数可使用：X-500,Y-600，Fc-600，Fs-0，Fa-0，at--200.仿真的本意是为了验证DSP上同类插补算法的正确性(Matlab M-file to prepare the CNC interpolation algorithm for 2D simulation of a straight line. Specific parameters can be used: X-500, Y-600, Fc-600, Fs-0, Fa-0, at- 200. The simulation is intended to verify the DSP on the correctness of the same interpolation algorithm)
- 2009-05-24 19:06:32下载
- 积分：1
-
WIDE-BAND
余割函数方向图的天线设计，其中给出了设计原理和实物图。(Cosecant pattern of the antenna design, which gives the design principle and the physical map.)
- 2013-11-07 10:12:29下载
- 积分：1
