-
clc
一维热传导模型,一维稳态热传导模型,有限差分法(One dimensional heat conduction model)
- 2018-09-15 08:40:17下载
- 积分:1
-
python神经网络求解农产品需求预测
使用BP神经网络预测农产品的需求,论文在知网上应该就一篇。(Using neural network to predict the demand of agricultural products)
- 2017-12-24 01:50:39下载
- 积分:1
-
oneapf
说明: 基于单位功率因数控制策略的单相有源滤波,去掉非线性负载部分即为单相全控整流。开关器件采用IGBT。(Based on the unity power factor control strategy of single-phase active power filter, remove the part of non-linear load is the single-phase full-controlled rectifier. Switching device IGBT.)
- 2009-08-06 20:09:07下载
- 积分:1
-
fftbianhuan
test1.txt 第一列为时间t,0.001s为步长;第二列为系统的输入信号;第三列为系统的输出信号。
signal_analyzer.m首先将test1.txt 的数据读入workspace,然后进行FFT,分析出两信号的频率,输出对于输入的幅值衰减(db),输出对输入的相位差。(test1.txt the first time as t, 0.001s for the step the second as the system input signal the third as the system output signal. signal_analyzer.m first test1.txt data read workspace, and then proceed to FFT, analysis of the two signals in the frequency, the output for input amplitude attenuation (db), the output of the input phase difference.)
- 2008-12-13 02:19:50下载
- 积分:1
-
Mesh2dv23
MATLAB编写的非结构化网格生成程序,不算很长(MATLAB program written in unstructured mesh generation, not very long)
- 2011-10-09 22:22:08下载
- 积分:1
-
powerflow33
33节点配电网前退回代法潮流计算程序。可以计算功率损耗,是至今为止比较完善的程序(33-node distribution network return on behalf of the flow calculation procedures. Can calculate the power loss, so far a relatively complete program)
- 2021-04-22 10:58:48下载
- 积分:1
-
DEAMATLAB-master
dea的ccr模型、超效率模型的m文件和实例(The CCR model of DEA, the M files and examples of the super efficiency model)
- 2017-12-18 18:16:18下载
- 积分:1
-
运用矩阵摄动法求解结构的复模态参数与动力特性等 matrixpre
运用矩阵摄动法求解结构的复模态参数与动力特性等(Application of Matrix Perturbation Method for Solving Complex Modal Parameters and other dynamic characteristics of the structure)
- 2017-03-28 09:08:42下载
- 积分:1
-
k-means-clustering
用C语言程序通过先随机选取K个对象作为初始的聚类中心。然后计算每个对象与各个种子聚类中心之间的距离,把每个对象分配给距离它最近的聚类中心。聚类中心以及分配给它们的对象就代表一个聚类。一旦全部对象都被分配了,每个聚类的聚类中心会根据聚类中现有的对象被重新计算。(C Programming Language by first randomly selected the K object as initial cluster centers. And then calculate the distance between each object and each seed cluster center, and assign each object to its nearest cluster center. Cluster centers, and the object assigned to them on behalf of a clustering. Once all the objects are assigned to each cluster cluster centers will be based on the existing object clustering is recalculated.)
- 2012-09-20 11:50:09下载
- 积分:1
-
yei-V4.2
自己编的5种调制信号,通过反复训练模板能有较高的识别率,DC-DC部分采用定功率单环控制。( Own five modulation signal, Through repeated training VxODOGFlate have higher recognition rate, DC-DC power single-part set-loop control.)
- 2017-04-19 08:49:21下载
- 积分:1