网站首页

Sa

于 2016-03-19 发布文件大小:1KB

 0  103

下载积分: 1 下载次数: 2

我要下载

代码说明：

说明： function [Sx,f,alpha] = Sa(s,fs,M,N,read_f,del_f) 计算信号的循环谱 [Sx,f,alpha] = Sa(s,fs,M,N,read_f,del_f) 输入： s 序列 fs 采用频率 M 滑动频率窗长 N fft计算点数 read_f 可视频率（一般为载频的整数倍） del_f 可视频率间隔输出： Sx 信号的循环谱 f 频率轴 alpha 循环频率轴(Cyclosationary Spectrum)

文件列表：

Sa.m,1192,2015-12-03

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

TL_inverter
这是个新型的单相三电平逆变器，用一个三电平桥臂和一个普通桥臂组成，SPWM控制。在MATLAB2008上运行(New type of single-phase three-level inverter PWM)

2012-02-28 11:25:18下载

积分：1
Gradient-Domain-HDR-Sourcecode
梯度域实现色调映射利用matlab函数实现fattal算法(Gradient Domain HDR Sourcecode)

2014-05-14 21:35:57下载

积分：1
qamsysterm
说明： m-qam调制解调系统仿真，包含调制解调的所有步骤(m-qam modulation and demodulation system simulation, including all steps of modulation and demodulation)

2009-09-01 09:31:01下载

积分：1
zuixuanminzufeng
用matlab的编程实现一首歌曲的播放。歌曲是用代码编辑的，运行后就能实现播放。(Realization of a song to play using matlab programming. The song is in code editor, can be achieved after playing running.)

2013-12-03 10:06:56下载

积分：1
mutal_music
说明：存在互耦情况下的均匀平面阵列的MUSIC估计及其校正方法(The existence of mutual coupling in case of uniform planar arrays MUSIC estimates and correction method)

2008-12-03 18:40:26下载

积分：1
PID-Control
常规PID、Smith预估补偿、改进的Smith、双控制器控制和内模的Simulink仿真图(Conventional PID, Smith, forecast compensation, the improved Smith, double control and internal model controller of Simulink simulation diagram )

2014-01-02 17:21:45下载

积分：1
Ultrawideband
超宽带（UWB）的多频带OFDM与定点transmitterreceiver物理层建模 UWB的分析超宽带的BPSK分析第五阶导数的BPSK超宽带超宽带信道模型超宽带链接分析超宽带单环超宽带单脉冲超宽带多旋回(Ultra-wideband (UWB) multiband OFDM physical layer with fixed-point transmitterreceiver modeling analysis of UWB UWB BPSK Fifth Order Derivative analysis of BPSK UWB UWB UWB channel model for UWB link analysis of UWB single-loop single-pulse ultra-wideband polycyclic)

2010-08-10 09:22:17下载

积分：1
geoFunctions
geo软件接收机的功能实现 matlab代码(geo functions matlab)

2012-05-13 20:58:13下载

积分：1
Sparse-Subspace-Clustering
Sparse Subspace Clustering

2014-02-20 08:12:51下载

积分：1
anfis
function [t_fismat, t_error, stepsize, c_fismat, c_error] ... = anfis(trn_data, in_fismat, t_opt, d_opt, chk_data, method) ANFIS Training routine for Sugeno-type FIS (MEX only). if nargin > 6 & nargin < 1, error( Too many or too few input arguments! ) end Change the following to set default train options. default_t_opt = [10 training epoch number 0 training error goal 0.01 initial step size 0.9 step size decrease rate 1.1] step size increase rate Change the following to set default display options. default_d_opt = [1 display ANFIS information 1 display error measure 1 display step size 1] display final result

2015-05-28 19:28:36下载

积分：1

696524资源总数
103945会员总数
46今日下载

Sa

0 个回复

热门标签

热门下载