-
基于QT实现的基础图形绘图系统.7z
说明： 输入椭圆中心和长短轴径;
2. 计算得到中心在原点的椭圆上的第一个点=;
3. 根据公式(1.1.3-2)计算区域1中决策参数的初值为;
4. 在区域1中每个位置处，从开始，反复按照公式(1.1.3-3)更新决策参数，若决策参数小于0则不变，反之加1，一直循环到为止，记第一个满足此条件的点为();
5. 在区域2的每个位置处，从开始，反复按照公式(1.1.3-6)更新决策参数，若决策参数小于0则不变，反之加1，一直循环到()为止;(Input ellipse center and long and short axis diameter;
2. The first point of the center on the ellipse at the origin is calculated.
3. According to formula (1.1.3-2), the initial value of decision-making parameters in region 1 is calculated.
4. At each location in region 1, the decision-making parameters are updated repeatedly according to formula (1.1.3-3). If the decision-making parameters are less than 0, they will remain unchanged. If the decision-making parameters are less than 0, then add 1 and cycle until the first point satisfying this condition is ();
5. At each location of region 2, the decision parameters are updated repeatedly according to the formula (1.1.3-6). If the decision parameters are less than 0, they will remain unchanged. If the decision parameters are less than 0, then add 1 and cycle until ().)
- 2020-11-13 16:49:42下载
- 积分：1
-
这个是Xilinx编程的源码，是Bristol大二时写的．
这个是Xilinx编程的源码，是Bristol大二时写的．-Xilinx is the programming source code, is sophomore at Bristol writes.
- 2022-11-23 21:55:04下载
- 积分：1
-
refprop_matlab
说明： 一个确实可以使用的通过matlab调用真实物性的文件(A file that can be used to call the real property through MATLAB)
- 2020-10-23 17:14:26下载
- 积分：1
-
该源码是关于数控仿真的程序
程序通过提取dxf格式文件，经过程序的处理得到数控G代码，最后进行加工仿真...
该源码是关于数控仿真的程序
程序通过提取dxf格式文件，经过程序的处理得到数控G代码，最后进行加工仿真-The source code is about the process of NC simulation program by extracting dxf format file, after proceedings which are CNC G code, and last, machining simulation
- 2023-05-15 11:05:02下载
- 积分：1
-
KEISOKU GIKEN 6605
说明： KEISOKU GIKEN 6605 EPROM Backup
- 2020-02-19 04:02:05下载
- 积分：1
-
《电动机的DSP控制——TI公司DSP应用》——王晓明——配套光盘程序
《电动机的DSP控制——TI公司DSP应用》——王晓明——配套光盘程序，北航出版社出版
- 2019-04-19下载
- 积分：1
-
本文介绍UNICODE编码规范，转载，最近正在搞这方面的东西，希望能给大家提供帮助，...
本文介绍UNICODE编码规范，转载，最近正在搞这方面的东西，希望能给大家提供帮助，-this paper UNICODE coding norms, reprinted recently in this regard is now pursuing things, I hope that it provides help, thank you
- 2022-11-27 04:50:03下载
- 积分：1
-
0 相控阵的书籍
说明： 这是有关相控阵的书籍，介绍很全面而且翔实，有关超声发射和聚焦方法介绍等(This is a book about phased arrays, the introduction is very comprehensive and informative, about the introduction of ultrasound transmission and focusing methods, etc.)
- 2021-01-20 15:43:43下载
- 积分：1
-
embeddedvideo
说明： 一般消费类电子产品常用视频简介，包括文件格式，基本算法等(embedded video)
- 2010-03-22 22:11:21下载
- 积分：1
-
wide_band
基于CSM自适应波束形成——酉聚焦
％ 8阵列；
％信噪比为10dB 干扰噪声比为20dB 干扰信号与需要信号不相关.
％干扰和信号频率所在范围为80—120Hz，相对带宽为40％ ，入射角度分别为seta_S_reg、seta_J_reg (CSM-based adaptive beamforming- Unitary Highlights 8 array 10dB signal to noise ratio for the interference noise ratio of 20dB interference signal and the need to signal irrelevant. Interference and signal frequency range is where the 80-120Hz, the relative bandwidth of 40 , respectively angle seta_S_reg, seta_J_reg)
- 2020-07-10 23:38:54下载
- 积分：1
