登录
首页 » matlab » 11111

11111

于 2020-09-18 发布 文件大小:1KB
0 211
下载积分: 1 下载次数: 6

代码说明:

  MATLAB齿轮轮廓仿真,根据齿轮的齿数,模数,压力角等参数可以得出齿轮的轮廓(Gear contour simulation)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CKF
    卡尔曼滤波算法,容积卡尔曼滤波算法实现,可以直接使用(Calman filtering algorithm,The volume Calman filtering algorithm is implemented, which can be directly used.)
    2018-04-13 10:02:34下载
    积分:1
  • verilog
    verilog-wire a simple circuits
    2023-02-08 20:15:03下载
    积分:1
  • DEVexpress chartControl demo
    说明:  DEVexpress chartControl demo DEV图形demo,各种控件的使用实例,供大家参考(DEVexpress chartControl demo)
    2020-06-18 05:00:01下载
    积分:1
  • 1.kriging2D
    说明:  二维克里金插值,用于将散点插值成二维矩阵(Two dimensional Kriging interpolation, which is used to interpolate scattered points into two-dimensional matrix)
    2020-04-25 21:57:42下载
    积分:1
  • 西门子s7-200自由口与多功能电表DLT645协议通讯
    说明:  用S7-200自由口与安科瑞多功能电表通讯 ,读出五个变压器的当前正向有功电度,分开每天谷 峰 平段电度,保存31天,并读出变压器电流,计当前功率. 减轻电工劳动强度,动力室抄表更加灵活性(Communication between Siemens Freeport and Intelligent Meter 645 Protocol)
    2021-02-28 08:09:35下载
    积分:1
  • stress-and-strain-analysis-ansys
    两个关于ansys的应力与应变方面的详细实例分析,容易入门与操作(Two stress and strain on the aspects of detailed case studies on ansys, easy entry and operation)
    2013-07-10 09:15:52下载
    积分:1
  • SWSIFT
    说明:  可对两幅图像的相似特征点进行匹配,并标记出对应特征点,同时对两幅图的相似点进行连线。(It can match the similar feature points of the two images, mark the corresponding feature points, and connect the similar points of the two images at the same time.)
    2020-06-17 16:11:50下载
    积分:1
  • 一套简单的购物车程序,由外国人编制,功能及实现方式都不错。...
    一套简单的购物车程序,由外国人编制,功能及实现方式都不错。-a simple Cart procedures by foreigners establishment, functions and the ways are good.
    2023-01-16 11:15:04下载
    积分:1
  • right no other assembly parts and the permanent link to the assembly of plastic...
    对不用其他装配零件而永久性联结的塑料零件的装配可采用焊接方法。焊接方法的选择依据以下几种标准:根据模塑零件的几何形状,所使用的原料, 成本、总生产周期的综合因素,装配部位所要求的机械性能和外观质量。-right no other assembly parts and the permanent link to the assembly of plastic parts available welding methods. Welding method of choice based on the following criteria : Molded parts of the geometry, the use of raw materials, cost, Total production cycle by a combination of factors, the assembly of parts required by the mechanical properties and appearance of quality.
    2022-03-28 19:31:14下载
    积分:1
  • kaba key 2009 kaba key 2009
    kaba key 2009 kaba key 2009
    2022-07-23 11:13:29下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载