-
828DPLC
西门子828d数控系统PLC程序。支持四轴控制及圆盘式刀具自动交换装置(Siemens 828d CNC PLC program. Axis control and disc support automatic tool exchange device)
- 2021-04-22 17:28:48下载
- 积分：1
-
CRC-C
有关 C语言的CRC校验的资料，很实用，值得收藏和学习(About the C language, the CRC data, it is practical, it is worth collecting and learning)
- 2014-04-15 18:33:56下载
- 积分：1
-
AuthScheme
This interface represents an abstract challenge-response oriented authentication scheme.
- 2014-07-11 10:55:07下载
- 积分：1
-
MSP430-MAX31856
说明： MAX31856测试程序，MSP430F5342通过端口模拟SPI总线操作MAX31856,并将采集到的数据通过UCA1串口发送.硬件上采用隔离电源,隔离通讯接口.多路热电偶信号经多路电子开关选通后再采集.仅供参考,实验室调试通过,未投入实用.
压缩包内容:
1.MSP430程序源代码.包括测试程序及加了协议的多路采集程序.
2.硬件电路图.PDF格式,包括电路板原理图,PCB布局图,元件清单.
3.MAX31856芯片手册及官方例程.
4.PC端程序(通讯协议仿的迅威科技8通道热电偶温度变送器的协议,所以他们的PC端测试程序应该也是可用的)
整理时间:2020年4月15日(MAX31856 test procedure, MSP430F5342 simulates the SPI bus to operate the MAX31856 through the port, and converts the collected data to serial transmission through UCA1. The hardware uses isolated power supply and isolated communication interface. Reform reference, laboratory debugging passed, not occupied practical.
Compressed package content:
1. MSP430 program source code. Including test procedures and multi-channel acquisition procedures with added protocols.
2. Hardware circuit diagram. PDF format, including circuit board schematic diagram, PCB layout diagram, component list.
3. MAX31856 chip manual and official routines.
4. PC-side program (the communication protocol is a copy of the Xunwei Technology 8-channel thermocouple temperature threshold protocol, so their PC-side test program should also be available)
Arrangement time: April 15, 2020)
- 2020-04-15 12:04:45下载
- 积分：1
-
dianzhen_1
字模软件取模代码之后，8*8点阵按照代码显示出相对应的字符与简单汉。(After modulus matrix software code, 8* 8 dot matrix display in accordance with a code corresponding to the character and simple Chinese.)
- 2013-12-17 14:52:10下载
- 积分：1
-
STM32超声波
STM32f103ZET6控制超声波测距模块，通过串口显示(STM32f103ZET6 controls the ultrasonic ranging module, which is displayed through serial port.)
- 2019-05-17 10:00:25下载
- 积分：1
-
CyUSBSerial_v3.0.11.0
Zedboard上板载有一个USB转UART串口，采用了Cypress公司的USB-UART控制器CY7C64225。Zedboard的USB驱动安装很简单，首先下载USB驱动程序，解压缩后会有3个子目录分别对应Windows XP、Windows Vista和Windows 7系统，根据自己的计算机系统选择。(Onboard there Zedboard a USB-to-UART serial port, using Cypress' s USB-UART controller CY7C64225. Zedboard USB driver installation is very simple, first download the USB driver, unzip have three subdirectories corresponding to Windows XP, Windows Vista and Windows 7 systems, according to their own computer systems to choose from.)
- 2014-07-14 19:13:19下载
- 积分：1
-
2.程序
说明： 在此基础上，设计一种温度测量系统，能够检测温度，并通过按键调整温度的上下限值，若超过该限值，进行报警提示。该系统的硬件子电路主要用Protues仿真软件实现，具体的子电路包括：恒流源电路（TLC2543芯片）、信号放大调理电路（两线制铂电阻PT100）、单片机最小系统（AT89C51）、A/D转换电路、按键电路、显示电路、声光报警器等。该系统的软件电路以C语言为基础，在Keil中实现。最后通过软硬结合，实现电路的各种情况仿真，以此验证电路设计的正确性和合理性。(On this basis, a temperature measurement system is designed, which can detect the temperature and adjust the upper and lower limits of the temperature by pressing the key. If it exceeds the limit, an alarm will be given. The hardware sub circuit of the system is mainly realized by Proteus simulation software. The specific sub circuits include: constant current source circuit (TLC2543 chip), signal amplification and conditioning circuit (two-wire platinum resistance PT100), minimum system of single chip microcomputer (AT89C51), a / D conversion circuit, key circuit, display circuit, sound and light alarm, etc. The software circuit of the system is based on C language and implemented in keil. Finally, through the combination of hardware and software, the circuit simulation is realized to verify the correctness and rationality of the circuit design.)
- 2021-01-20 10:36:29下载
- 积分：1
-
新手调试 开发板配套例程
对于新手调试入手很快,通过32单片进行通信控制,及算法运算。(For beginners, debugging starts very quickly, communication control is carried out through 32 single chip, and arithmetic operation is given to them.)
- 2020-06-25 03:40:02下载
- 积分：1
-
430
用MSP430F149写的读写SD卡的程序，用SPI总线的模式实现对sd卡的读写访问。(MSP430
spi
sd)
- 2020-10-05 11:17:38下载
- 积分：1
