登录
首页 » matlab » 反射式血氧(SPO2)计算

反射式血氧(SPO2)计算

于 2016-05-12 发布 文件大小:2KB
0 243
下载积分: 1 下载次数: 39

代码说明:

  反射式血氧(SPO2)计算,包括基线滤波,脉搏波特征点提取,R值计算,可移植到单片机(STM32)(Reflective oximetry (SPO2) calculations, including baseline filtering, pulse wave feature point extraction, R value calculation, can be transplanted to the microcontroller (STM32))

文件列表:

spo2_test.m,8448,2016-05-09

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • duojihuizongbi
    舵机使用说明,用于实现对舵机的控制。其中讲述了舵机的各种使用说明。(Steering instructions, used to implement the control of the steering gear. Various instructions which tells the story of steering gear.)
    2014-04-18 09:31:22下载
    积分:1
  • 33WZH8008
    液晶例程, 包括画点画线画缓冲条,在液晶上printf的算法(LCD program world,you can study LCD draw points )
    2013-08-06 11:00:33下载
    积分:1
  • Temperature-display
    一个单片机应用的代码,可实现基于单片机的温度数码管显示,经验证可编译通过并实现(A microcontroller application code, enabling microcontroller-based digital temperature display, proven to compile and implement)
    2011-12-13 12:37:47下载
    积分:1
  • switch
    用单片机AT89S51实现的模拟开关灯系统(MCU AT89S51 realize the analog switch lamps system)
    2008-05-15 21:25:02下载
    积分:1
  • rgy
    红绿灯控制程序,基于stc51系列单片机(Traffic light control program, based stc51 series microcontroller)
    2012-12-19 16:14:47下载
    积分:1
  • sensor
    仅使用一个热敏电阻和一个10K电阻、104电容,在MSP430上实现的精度可达0.1度的温度测量代码。(Only using a thermistor and a 10K resistor, capacitor 104, temperature measurement code achieved accuracy up to 0.1 degree on the MSP430 .)
    2013-12-17 08:16:48下载
    积分:1
  • STC89C52_m
    此程序可实现长度为8位,周期为255的m序列,此序列可当做伪随机信号发生器,模拟信道噪声。(This procedure can achieve the length of 8 bits, the m sequence of 255 cycles, the sequence can be used as a pseudorandom signal generator, analog channel noise.)
    2021-01-02 23:18:57下载
    积分:1
  • ADC
    c8051 mcu 单片机 adc程序。全部c8051适用(c8051 adc)
    2011-04-22 09:43:50下载
    积分:1
  • STM32KEY_2015_03_27_11_01_25
    本例程基于STM32F103RC系列ARM单片机的外部按键测试程序(This routine is based on external key test program of STM32F103RC series ARM microcontroller)
    2015-03-27 11:08:19下载
    积分:1
  • lesson9_1
    在51开发板上,向AT24C02 EEPROM中写入0x(xx),同时读出之后赋值给P1口。注意三处加*********(In the 51 development board, write 0x (xx)to AT24C02 EEPROM , while after reading assigned to P1 port. Note that three plus。)
    2013-07-19 17:20:46下载
    积分:1
  • 696518资源总数
  • 106174会员总数
  • 31今日下载