登录
首页 » matlab » code

code

于 2021-01-25 发布 文件大小:214KB
0 255
下载积分: 1 下载次数: 5

代码说明:

  光纤耦合仿真MATLAB程序包,可以仿真不同芯径的光纤模式分布,可以仿真光纤的耦合损耗。(fiber coupling simulation)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • swarmoptimizationformutiobjectiveopimization
    里面包含有几个非常好的基于粒子群优化的算法和基于matlab的源程序,对研究粒子群和优化的朋友很有帮助。(Which contains a few very good based on particle swarm optimization algorithm and matlab based on the source, the study of particle swarm optimization and helpful friends.)
    2007-09-13 15:37:10下载
    积分:1
  • ebook-OreillyCInANutshellDec2005
    C:In a Nutshell(.chm) Author: Tony Crawford, Peter Prinz Publisher: O Reilly Pub Date: December 2005
    2007-09-26 19:53:20下载
    积分:1
  • EigenFace
    the code of eigenface
    2012-01-05 11:05:45下载
    积分:1
  • cucaoji
    利用粗糙集实现对数据的清洗,清洗掉无效的数据(he use of rough set to achieve the data cleaning, cleaning out invalid data)
    2017-04-27 16:59:22下载
    积分:1
  • optical
    Optical communication budget
    2010-09-18 22:45:30下载
    积分:1
  • adptive
    雷达直达波和目标回波之间抵消,两个信号一强一弱,既可以抵消强信号,也可以抵消弱信号(Radar direct wave and the target echo offset between the two signals a strong one weak, only to be offset by a strong signal, you can also offset the weak signal)
    2009-12-18 17:38:35下载
    积分:1
  • FaceForWeb
    Face for web is a feature of this Code and you can find out the reduce the size of an image according to the requirements you want so that it can be uploaded to the web using mtlab.
    2010-12-26 13:52:30下载
    积分:1
  • zonghe3
     检查数据:如果某一组转速N下数据点少于5个点,给出提示:“数据点少不能绘制曲线”。  插值:每一条转速N线上的测量点个数可能不一样,按照测量点数最多的个数,将测量点少的数据插值成测量数据点最多一样的个数 ( check data: If a group speed N under the data point is less than 5 points, hints: " The few data points can not draw a curve. The  interpolation: each a speed N line, the number of measurement points may be different, in accordance with the maximum number of measurement points, the measurement point less data is interpolated to the measurement data points up the same number of)
    2013-01-20 23:17:27下载
    积分:1
  • izak
    对输入的信号进行zak逆变换,观察滤波后的信号在时域的分布情况(used to analysis the izak transform, so that wo can know the distribution of the processing signal)
    2014-12-02 09:53:34下载
    积分:1
  • send
    参考3GPP相关标准并根据LTE技术特征和关键特性,对下行链路级进行设计,包含以下步骤:比特生成、CRC校验、码块分割、编码、速率匹配、码块级联、加扰、调制、层映射、预编码、资源映射、OFDM符号生成和天线映射。为模拟无线传输信道,还需仿真相应的信道模型。收端则是发端的严格逆过程,对接收信号进行一系列处理,得到代表原始发送的信息并判决。(References 3GPP LTE technology standards and in accordance with characteristics and key characteristics of the downlink stage design, comprising the steps of: generating bits, CRC checksum, code block segmentation, encoding, rate matching, code block concatenation, scrambling, modulation , layer mapping, precoding, resource mapping, OFDM symbol generation and antenna mapping. Analog wireless transmission channel, the need to emulate the corresponding channel model. The receiving end is the inverse of the originator of the rigorous, a series of processing the received signal, the representation of the original transmitted information and judgment.)
    2013-10-08 09:39:40下载
    积分:1
  • 696518资源总数
  • 106242会员总数
  • 10今日下载