-
music
这一课我们用 4 个按键来控制播放音乐。K1－K3 每个键播放一首音乐，K4 按键停止
音乐的播放
(this)
- 2010-10-17 16:25:42下载
- 积分：1
-
multicarriers_modulations
Amplitude Clipping and Iterative Reconstruction of
MIMO-OFDM Signals with Optimum Equalization
- 2010-12-16 02:34:39下载
- 积分：1
-
read_dxf
matlab读取dxf。有点和样条线的限制。(matlab read the dxf. A little bit and kind of line constraints.)
- 2010-05-25 09:18:53下载
- 积分：1
-
butterworthlowpass.rar
butterworth低通滤波器的原程序，可用ＭＡＴＬＡＢ的ＦＩＬＴＥＲ函数测试．可得到低通滤波器数字系统函数的系数．(Butterworth low-pass filter the original procedure, MATLAB can be used to test the FILTER function. Available to low-pass filter function of the coefficient of digital systems.)
- 2007-12-03 11:14:19下载
- 积分：1
-
tricurv.tar
Function to calculate the principal curvatures on a triangular mesh. Approximations of curvature are based on local (N=1) neighborhood elements and vertices.
Note: Directions of curvatures aren t calculated appropriately. Will post an updated version once this is implemented.
Note that calculations at vertices with few adjacent triangles, and hence few adjacent vertices, are expanded to a greater neighborhood.
Reference:
1) Chen and Schmitt (1992) Intrinsic surface properties from surface triangulation
2) Dong et al. (2005) Curvature estimation on triangular mesh, JZUS
This code makes use of routines: buildInverseTriangualtion.m & removeDO.m
initially written by: David Gringas. He is gratefully acknowledged
- 2010-12-13 23:52:29下载
- 积分：1
-
load-analysis
电力系统负荷分析，并带有同步调相机，欢迎下载(Power system load analysis, with synchronous condenser, welcome to download)
- 2013-04-10 12:31:14下载
- 积分：1
-
diyiceshi
10个阵元半波长间距的ULA,请画出其波束0度、-20度和45度的波束方向图，并计算其波束宽度(10 half-wavelength spacing array element ULA, please draw its beam 0 degrees, 20 degrees and 45 degree beam pattern, and calculate its beamwidth)
- 2014-12-26 20:44:51下载
- 积分：1
-
Untitled
三次样条曲线插值函数的matlab源程序(three spline curvs)
- 2011-05-26 13:13:57下载
- 积分：1
-
mp
说明： 该算法是贪婪算法mp的matlab程序，用于信道估计等等(The algorithm is greedy mp' s matlab program for channel estimation, etc.)
- 2011-10-07 14:28:05下载
- 积分：1
-
mofang
魔方还原程序,主函数为Cube,采用CFOP，还原步骤为88步左右，底面十字未优化；采用留个3*3矩阵，前面为froo（数字3），后面为baa（数字-3），左面为leff（数字-2），右面为rigg（数字2），上面为upp（数字0），下面为doo（数字1），(Cube restore process, the main function of Cube, using CFOP, the reduction step is 88 steps or so, the bottom cross unoptimized adopt leave a 3* 3 matrix, in front of froo (figure 3), followed by the baa (figure-3), left the leff (digital-2), the right of rigg (figure 2), at the upp (number 0), following the doo (figure 1),)
- 2013-11-01 14:41:59下载
- 积分：1
