-
WS_net
通过设置不同的参数，创建小世界网络，用于仿真建模。(This program is to create a small world network for simulation.)
- 2020-06-19 01:20:02下载
- 积分：1
-
Desktop
说明： abaqus 帮助文档中的蠕变本构模型，包括时效强化模型和应变强化模型，以及一个模型的inp文件(Creep constitutive model in abaqus help document, including time-based reinforcement model and strain reinforcement model, and inp file of a model)
- 2020-06-22 16:00:01下载
- 积分：1
-
可见光通信最大化最小速率_matlab
说明： 计算可见光通信中最大化最小速率的优化问题，还有稳健波束成形(The optimization problem of maximizing the minimum rate and robust beamforming are also discussed)
- 2020-08-11 20:08:27下载
- 积分：1
-
chapter5attitude
说明： 卫星姿态是指卫星星体在轨道上运行所处的空间指向状态。将直角坐标系的原点置于星体上，指向地面的Z轴反映偏航方向，Y轴反映俯仰方向，X轴反映滚动方向。星体在高空中沿局部地球铅垂方向和轨道矢量方向运行，不时地产生对三轴的偏移。姿态控制是通过姿态控制分系统（ACS）来实现，使用地平扫描仪可感应俯仰和滚动轴的姿态误差，使用速度陀螺仪和罗盘可感应偏航轴的姿态误差。(Satellite attitude refers to the spatial orientation of a satellite in orbit. The origin of the Cartesian coordinate system is placed on the star, the Z axis pointing to the ground reflects the yaw direction, the Y axis reflects the pitching direction, and the X axis reflects the rolling direction. The stars move along the direction of the earth's vertical direction and the orbit vector in the high altitude, resulting in the deviation of the three axis from time to time. Attitude control is realized by attitude control subsystem (ACS). The attitude error of pitch and rolling axis can be induced by using horizon scanner, and the attitude error of yaw axis can be induced by using speed gyroscope and compass.)
- 2017-10-29 16:46:09下载
- 积分：1
-
SOM
说明： 自组织映射神经网络，直接就可以流畅的运行出仿真效果图处理。(The self-organizing mapping neural network can directly run smoothly to process the simulation renderings.)
- 2020-04-24 14:10:00下载
- 积分：1
-
test
说明： 将一个50Hz的干扰信号加入到白噪声中，然后对合成信号做fft，得到相应的幅频谱图和相位谱图。(A 50 Hz interference signal is added to the white noise, and then the composite signal is FFT to get the corresponding amplitude spectrum and phase spectrum.)
- 2021-03-10 00:04:45下载
- 积分：1
-
2dcohesive
说明： 平面用cohesive单元模拟仿真裂纹扩展和结构失效，裂纹扩展(Plane simulation of crack growth and structure failure, crack growth with cohesive element)
- 2019-11-21 10:38:54下载
- 积分：1
-
第十次作业
说明： 一受均匀拉力的板，中心带贯穿裂纹，裂纹长2a，使用4节点单元计算裂尖应力分布和应力强度因子(A uniform tensile plate with a through crack in the center and a crack length of 2a is used to calculate the stress distribution and stress intensity factor at the crack tip using a four node element)
- 2020-03-04 18:02:13下载
- 积分：1
-
第五章
机械动力学进行模态分析，频响应分析等动力学的分析(Modal analysis, frequency response analysis and other dynamic analysis of mechanical dynamics.)
- 2018-10-25 09:31:36下载
- 积分：1
-
单个圆形活塞换能器指向性
使用matlab进行超声波阵列指向性仿真(Simulation of directivity of ultrasonic array using MATLAB)
- 2021-04-04 15:09:04下载
- 积分：1
