登录
首页 » Proteus » 电子种-CZY

电子种-CZY

于 2017-11-20 发布 文件大小:103KB
0 227
下载积分: 1 下载次数: 1

代码说明:

  基于proteus的电子钟,可以显示时间,更改时间(Electronic clock, display time, can change the time)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • at91sam9260-df-recovery-v1.0
    at91sam9269 recovery flash
    2010-05-22 20:03:57下载
    积分:1
  • main
    8051f300 128码 识别程序,对特殊128码进行过滤(8051f300 128 code identification procedures, a special filter Code 128)
    2011-05-17 22:06:36下载
    积分:1
  • cat24wc02
    这是Small RTOS 51 在DP-51下载仿真实验仪上使用CAT24WC02驱动程序的例子。本例程序按照相应的的通讯协议接收一个数据,并将接收到的数据显示到LED数码显示器上。然后将接收到的数据写入Cat24Wc02中,再在同一位置将数据读出,并将读出的数据通过串口发送回来。通讯协议参考rtos随想曲和test.ini。 (This is the Small RTOS 51 DP-51 download simulation NG use CAT24WC 02 Driver for example. The cases in accordance with the relevant procedures of receiving a communication protocol data and receiving the data shows that the LED digital display. Then sending the data into Cat24Wc02, again in the same position will be read out data, will be read out through the serial data sent back. Communication protocol reference rtos test.ini and Capriccio.)
    2006-09-11 09:59:05下载
    积分:1
  • proteus-simulation-DC-power-supply
    proteus仿真+程序关于数控直流稳压电源,毕业设计的,也可用于课程设计(proteus simulation program on+ NC DC power supply, graduation design can also be used for curriculum design)
    2021-04-06 23:29:02下载
    积分:1
  • 130110
    控制蜂鸣器pic18单片机程序,测试通过,已批量生产。(Pic18 microcontroller program to control the buzzer)
    2014-01-24 10:44:16下载
    积分:1
  • adc
    说明:  这是一个基于PIC的AD转换,希望对大家有用(AD FOR PIC...)
    2009-08-10 12:03:22下载
    积分:1
  • 51风力摆
    使用MPU6050,串口通讯,PID算法,可完成题目所有要求(this is a Wind pendulum)
    2020-06-22 04:00:01下载
    积分:1
  • test
    通过按键控制直流电机的转动和停止,其中按键1转动,按键2停止。(Through buttons control the rotation of the DC motor and stop the rotation of the button 1, button 2 to stop.)
    2013-04-09 20:51:11下载
    积分:1
  • DDS
    说明:  直接频率合成仿真源程序,希望有人能用到.(Direct frequency synthesizer simulation source code, hope someone can use to.)
    2008-09-07 21:37:30下载
    积分:1
  • STM32_MPU-6050
    本例程使用GPIO模拟I2C时序访问三轴陀螺仪芯片MPU-6050。通过串口实时打印MPU-60505的采样数据,每秒刷新一次显示。(The routine use of analog I2C GPIO Timing visit triaxial gyroscope chip MPU-6050. Real-time printing through the serial port MPU-60505 sample data, display refresh every second.)
    2020-12-14 08:49:14下载
    积分:1
  • 696516资源总数
  • 106648会员总数
  • 8今日下载