登录
首页 » matlab » band diagram of 2D photonic crystal

band diagram of 2D photonic crystal

于 2020-07-04 发布 文件大小:3KB
0 201
下载积分: 1 下载次数: 3

代码说明:

  通过使用平面波发计算光子晶体能带图,这个图是我自己弄的,非常辛苦。但是希望能给从事光学研究的朋友的带来帮助。(Calculating the bandgap of a photonic crystal by using a plane wave gives me a very hard picture of myself. But I hope to help those who engage in optical research.)

文件列表:

band diagram of 2D photonic crystal.m, 11269, 2017-11-12

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Multiscalemm
    数学形态学用于技术分析ECG心律的探测,很不错的(mathematical morphology for technical analysis of the ECG arrhythmia detection, very good)
    2007-03-05 15:51:12下载
    积分:1
  • channel8
    信道划分代码。它是做通信算法的基础。可以模拟简单的信道变化。(Channel code division. It is the basis for the algorithm to do communications. Can simulate a simple channel change.)
    2010-08-10 16:42:17下载
    积分:1
  • SVC
    SIMULINK下包含SVC的稳态和暂态仿真系统模型(SIMULINK under contain SVC steady-state and transient simulation system model)
    2013-03-05 16:17:51下载
    积分:1
  • APF
    Low-pass filter 可自行調整延遲角度(Low-pass filter)
    2014-10-29 19:46:12下载
    积分:1
  • errorcate
    这是一个计算误码率的文档,里面包含源码及说明,很容易理解(This is a documentation error rate calculation, which contains the source code and instructions, it is easy to understand)
    2011-04-25 17:07:41下载
    积分:1
  • F
    说明:  对曲线进行拟合,使得最后拟合的数据与元数据的误差最小(The curve fitting, so that the final fitting of the data with the metadata minimum error)
    2013-09-22 15:54:47下载
    积分:1
  • Capacity_8PSK
    8PSK 调制,AWGN信道下的信道容量的matlab 仿真程序。(8PSK modulation, channel capacity under AWGN channel matlab simulation program.)
    2014-10-05 17:37:41下载
    积分:1
  • bottom_up_segmentation
    这是TD算法的逆过程,首先将时间序列,划分为相邻点的短序列,当然此时的拟合误差为0,因为第一点和第二点的连线,原始点都落在线段上。将相邻两个线段连接起来,此时每条线段包含三个原始点,计算中间那个点的拟合误差。这样,所有这些三个点的线段中的中间点的拟合误差计算出来后,找出误差最小且误差小于阀值R的分段,作为第一条包含三个点的线段。 在上面的基础上,第一条分段同样的和相邻线段连接,然后计算每一条分段的拟合误差,再找出误差最小且小于阀值R的分段,作为第二个分段。依次方式循环,直到所有分段的拟合误差都小于阀值R,分段结束。 (This is the reverse process of TD algorithm, the first time series is divided into short sequences adjacent dots, of course fitting error is zero at this time, because the first and second points of connection, the original point fall line on. The two adjacent segments are connected, then each segment contains three original point, the intermediate fitting error calculated that point. Thus, after all these segments fitting error of three points in the intermediate point calculated to find the minimum error and the error is less than the threshold R segment, as the first line contains three points. Based on the above, the first segment and the adjacent line segment connecting the same, and then calculate a fitting error for each segment, and then find the smallest error and less than the threshold R segment, as the second segment . Followed by a cyclic manner until all segments fitting error is less than the threshold R, segment ends.)
    2021-03-20 16:29:18下载
    积分:1
  • Introduction-to-Simulink-with-Engineering-Applica
    A book for MATLAB beginners
    2013-09-05 05:40:56下载
    积分:1
  • CFAR Processors
    说明:  里面包含详细的CFAR公式推导及原理,里面的公式可以对照雷达信号处理基础一书中的第七章部分(It contains detailed derivation and principle of CFAR formula.)
    2019-07-09 16:18:33下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载