登录
首页 » matlab » woptics.fresnel_equations

woptics.fresnel_equations

于 2016-07-22 发布 文件大小:4924KB
0 259
下载积分: 1 下载次数: 18

代码说明:

  comsol仿真平面电磁波在自由空间传播入射一个角度 在无限电介质。该模型计算的反射和 透射系数,并比较结果到菲涅耳方程。(A plane electromagnetic wave propagating through free space is incident at an angle upon an infinite dielectric medium. This model computes the reflection and transmission coefficients and compares the results to the Fresnel equations.)

文件列表:

models.woptics.fresnel_equations
................................\fresnel_equations.mph,4489166,2015-09-29
................................\models.woptics.fresnel_equations.pdf,814841,2015-09-29

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • fusion
    说明:  配电网规划必须满足辐射性和连通性,配电网扩展规划问题随机产生的初始群体中往往存在大量不可行解,采用根节点融合法可确保方案的可行性。(Distribution network planning must meet radiation and connectivity, distribution network expansion planning problem with randomly generated initial population there is often a large number of infeasible solutions, use of root fusion method to ensure feasibility.)
    2010-05-04 09:37:43下载
    积分:1
  • OFDM
    首先根据短训练字的特性进行相关运算,进行信号到达检测,当检测到相关值大于门限一定次数后,认为有信号到达。然后根据长训练字的特性,进行相关运算,进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后,先在时域进行小频偏的估计,将两个长训练字进行小频偏补偿后,进行FFT运算,根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后,就可以进行数据解调了。先对数据部分进行完整的频偏补偿,然后根据估计的FFT窗口位置进行FFT运算得到频域的数据,进行解调。然后在对应于导频的子载波位置上提取出导频信息,根据导频信息估计出剩余定时误差以及剩余的信道响应误差,将误差量送入环路进行跟踪。当收到所有数据后,重新回到信号到达检测状态,进行下一次信号到达的检测和信号接收。(First, according to the characteristics of the short training word correlation operation, the signal reaching the detector, when the detected correlation value is greater than the threshold after a certain number of times that a signal arrives. And then the characteristics of long training word, the correlation operation for the FFT window starting position of an OFDM symbol estimate. The estimated position of the FFT window, the first small frequency offset in the time domain estimation, the two long training word small frequency offset compensation, the FFT operation, the FFT result of the operation for integer frequency offset estimate. These parameter estimation is completed, the data can be demodulated on. The first portion of the data for a complete frequency offset compensation, and based on the estimated FFT window position of the FFT operation to obtain frequency domain data, demodulated. Then corresponding to the position of the pilot subcarriers are extracted on pilot inform)
    2020-11-04 23:49:52下载
    积分:1
  • ZSI_with_filter
    IMPEDANCE SOURCE INVERTER WITH FILTER TO REDUCE THE THD WITHIN THE STANDARDS
    2010-09-26 22:57:54下载
    积分:1
  • final
    simulink model for optical cdma system which uses orthogonal code.
    2009-04-24 00:52:42下载
    积分:1
  • Harris_corner
    Harris corner detection MATLAB CODE
    2014-12-09 13:33:49下载
    积分:1
  • 颤振matlab序说明书
    该计算程序可以对无固定约束碰撞振动系统在激励力作用 下的系统响应进行计算,模拟系统动态响应,并自动判断颤振发生情 况,记录不同参数组合(阻尼比,质量比,恢复系数,间隙,频率比) 情况下系统的响应数据,输出发生颤振的参数组合数据。(The program can be used to study the impact force of a vibro impact system with no fixed constraint The system response is calculated, the dynamic response of the system is simulated, and the occurrence of chatter is judged automatically Different parameter combinations (damping ratio, mass ratio, recovery coefficient, clearance, frequency ratio) were recorded In the case of the system response data, the output parameters of flutter data are output.)
    2017-10-30 16:46:39下载
    积分:1
  • 3DGaussian
    说明:  利用高斯频谱产生三维的高斯随机起伏地表的小软件(generates 3D Gaussian random rough surfaces with Gaussian Spectrum.)
    2011-03-22 14:06:13下载
    积分:1
  • tv_reg
    This MATLAB .m file takes a "true" image, and an "observed" image that is the true image that has been noised with uncorrelated Gaussian noise. The function then performs Tikhonov regularization to clean up the defects in the image, with the Tikhonov term used to preserve image edges as much as possible.
    2011-04-27 11:29:32下载
    积分:1
  • matlab6.5source
    MATLAB6.5的图像处理源码 是从书上面摘录下来的 有具体章节(MATLAB6.5 Image Processing source from the above extract from the book down the specific sections)
    2007-05-20 09:41:11下载
    积分:1
  • export_fig
    将MATLAB生成的图表,数据和.fig等结果文件导出到其它文件中,(This function saves a figure or single axes to one or more vector and/or bitmap file formats, and/or outputs a rasterized version to the workspace, with the following properties: - Figure/axes reproduced as it appears on screen - Cropped borders - Embedded fonts (vector formats) )
    2009-10-10 22:18:17下载
    积分:1
  • 696518资源总数
  • 106010会员总数
  • 4今日下载