-
示波器
简单示波器，可以实现在前面板中显示各种波形图(Using LABVIEW to make Simple oscilloscope)
- 2019-06-14 12:07:25下载
- 积分：1
-
信噪比-误比特率曲线
说明： 使用Labview平台计算误码率，绘制误码率曲线，用于通信系统仿真。(Calculate the bit error rate and reconstruct the bit error rate curve)
- 2021-05-17 09:30:02下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
单服务器多客户机(1)
labview通讯案例，多线程一对多，实现多线程通讯(labview review eefefeffffffff adkadaapadadkada)
- 2019-04-01 14:08:02下载
- 积分：1
-
Wind-power-bearing-test
风电机组轴承的状态监测和故障诊断与运行维护(Wind turbine bearing condition monitoring and fault diagnosis and operation and maintenance)
- 2014-02-15 19:04:55下载
- 积分：1
-
ADS1115_stm32f10
用labview编写的采集温度的多个通道通讯的程序，用STM32的串口发送数据到电脑上(Prepared using the acquisition temperature of the multi-channel communication procedures, using STM32 serial port to send data to the computer)
- 2016-11-02 17:03:20下载
- 积分：1
-
signal-process
采用LABview编写的信号处理程序，包括各种滤波去噪等功能(Using LABview signal processing procedures, including a variety of filtering de-noising, and other functions)
- 2020-12-19 15:29:10下载
- 积分：1
-
手把手教你在LabVIEW下使用OPC
说明： Labview OPC和欧姆龙PLC通讯(LabVIEW OPC and OMRON PLC communication)
- 2020-03-04 19:39:21下载
- 积分：1
-
UI Messages TestStand LabVIEW OI
说明： 客户觉得TestStand界面复杂，希望一个简单的界面即可进行序列执行，采用LabVIEW调用TestStand引擎可实现快速设计，将TestStand拆解到LabVIEW。
然而，这样做需要设计大量回调函数，开发较费时间，项目对时间要求很严格，且投入不多，故希望有快速解决方案。
为此，设计时希望LabVIEW可以充当一个辅助软件，可配置和控制执行，进行简单数据交互，执行还是TestStand进行(The customer thinks that TestStand interface is complex, and hopes that a simple interface can be used for sequence execution. Using LabVIEW to call TestStand engine can realize rapid design and disassemble TestStand to LabVIEW. However, to do this, a large number of callback functions need to be designed, which takes a lot of time to develop. The project has strict time requirements and little investment, so we hope to have a fast solution. Therefore, it is hoped that LabVIEW can be used as an auxiliary software in the design, which can be configured and controlled for execution, simple data interaction, execution or TestStand)
- 2020-06-01 17:19:22下载
- 积分：1
-
Digit Oscilloscope
说明： 基于NI的LABVIEW开发平台的数字示波器开发实例(Development Example of LABVIEW Digital Oscilloscope)
- 2019-02-20 13:55:42下载
- 积分：1
