登录
首页 » matlab » maokan

maokan

于 2016-11-30 发布 文件大小:8KB
0 172
下载积分: 1 下载次数: 2

代码说明:

  一个计算声子晶体结构的一维传递矩阵法,在MATLAB中求图像纹理特征,Relief计算分类权重。( A one-dimensional transfer matrix method to calculate the phonon crystal structure, In the MATLAB image texture feature, Relief computing classification weight.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • pro_bhp
    this is one of the best satelite code in the world to find the look angle
    2013-08-23 12:03:07下载
    积分:1
  • sim-polar-3
    simulation BPSK on fading channel
    2015-04-15 16:23:23下载
    积分:1
  • eva
    基于Gumbel极值分析的腐蚀剩余寿命估计过程中,Gumbel分布图的绘制程序。该程序在论文“储罐底板机器人在线检测数据的极值分析”有应用。(Gumbel distribution graph plotting code for corrosion residual life estimation. The program is applied in the paper Extreme Value Analysis of In-Service Robotic Storage Tank Floor Inspection .)
    2017-04-07 10:40:04下载
    积分:1
  • bipolar
    line codes: bipolar of a bits secuence
    2013-12-12 08:42:57下载
    积分:1
  • untitled8
    基于单周期控制的升压型有源功率因数校正仿真图( Based on one cycle control boost active power factor correction simulation diagram)
    2015-04-17 15:26:32下载
    积分:1
  • 16qam
    16QAM通过带限信道,设码元速率为1000波特,传输的滚降系数是0.75的滚降升余弦滤波器(16QAM by band-limited channel, set the symbol rate is 1000 baud, roll-off factor of transmission is 0.75 rolloff raised cosine filter)
    2014-11-28 14:39:14下载
    积分:1
  • chuanliandiandan
    永磁同步电机直接转矩控制,转矩闭环,磁链闭环(Permanent magnet synchronous motor direct torque control, closed-loop torque, flux closed-loop)
    2013-05-11 21:39:48下载
    积分:1
  • abc
    multilevel inverter using variable dc source
    2014-02-11 04:13:20下载
    积分:1
  • HFSS_MATLAB_source-editing
    阵列天线多端口的馈电操作。在进行波束赋形或相控阵天线设计时,若天线端口数量巨大,可以用该程序一次实现对所有天线端口相位及赋值的输入。(Multi-array antenna feed port operations. Performing beamforming or phased array antenna design, if the huge number of antenna ports can be used to implement the program once all the input phase and the antenna port assignment.)
    2016-06-02 10:37:59下载
    积分:1
  • chufaqi
    触发器,eda.在实际的数字系统中往往包含大量的存储单元,而且经常要求他们在同一时刻同步动作,为达到这个目的,在每个存储单元电路上引入一个时钟脉冲(CLK)作为控制信号,只有当CLK到来时电路才被“触发”而动作,并根据输入信号改变输出状态。把这种在时钟信号触发时才能动作的存储单元电路称为触发器(Triggers, eda. The actual digital systems often contain a large number of memory cells, and at the same time they often require synchronized action, to achieve this purpose, the introduction of a clock pulse (CLK) in each memory cell circuit as a control signal , the arrival of the circuit only when CLK was only trigger the operation and change the output state of the input signal. The memory cell circuit that can trigger actions when the clock signal is called a flip-flop)
    2014-08-27 10:43:49下载
    积分:1
  • 696518资源总数
  • 105873会员总数
  • 12今日下载