-
gauss
说明： gauss积分matlab代码，一个完整的程序(matlab code gauss points, a complete program)
- 2011-04-09 02:08:40下载
- 积分：1
-
msk-in-matlab
用MATLAB编写与仿真了MSK信号，其中结合了自己写的快速傅立叶变换实现了MSK信号的调制还有解调，而且作为拓展，还加入噪声、通过带通滤波器、低通滤波器、载波信号等等。调制解调都很有用，画出的图也很漂亮规范。(Using MATLAB and the simulation of the MSK signal, which combines the fast Fourier transform to write their own modulation there demodulation of MSK signals, but also as a development, but also by adding noise, band-pass filter, low pass filter, the carrier signaland so on. The modem is very useful to draw the plan is also very beautiful and specification.)
- 2012-03-28 00:05:08下载
- 积分：1
-
matlab_chengxusheji
该MATLAB通过给出典型例子介绍了在MATLAB环境下进行程序设计的方法(through the MATLAB is a typical example of the MATLAB environment for the conduct of the program design)
- 2007-04-12 17:45:20下载
- 积分：1
-
路由优化算法（需要输入参数）
说明： 其路由优化包括能量收集，频谱感知和数据传输，DE最优算法等(Its routing optimization includes energy collection, spectrum sensing and data transmission, de optimal algorithm, etc)
- 2020-03-19 22:55:09下载
- 积分：1
-
BLDCM的simulink模型
说明： BLDCM的simulink模型，电流、转速双闭环控制的无刷直流电动机系统，电机模块是自己封装而成的不是用的永磁同步电动机或者自带的BLDCM，所涉及的三个程序也有展示。(The model of BLDCM, the BLDCM system with double closed-loop control of current and speed,and the motor module is a self packaged permanent magnet synchronous motor or BLDCM, and the three programs involved are also shown.)
- 2020-06-26 19:40:02下载
- 积分：1
-
用于地震信号的剖面生成 wigb
说明： 用于地震信号的剖面生成，有助于观察采集到的信号(For seismic signal profile generation, it is helpful to observe the collected signals)
- 2020-05-04 18:01:12下载
- 积分：1
-
r8_fj_noframe_bs
用matlab仿真的八路时分复用系统，包括变速复接巴克码解复(Matlab simulation with eight-way time-division multiplexing system, including the Barker code transmission multiplexing demultiplexing)
- 2010-06-03 11:42:38下载
- 积分：1
-
11
说明： 给予神经网络训练的MATLAB 程序 有很大的用处 解说的非常详细(Given the MATLAB neural network training procedures have great usefulness of the very detailed explanation)
- 2009-07-08 20:39:21下载
- 积分：1
-
LeastSquare
constrained linear least square implementation
- 2011-07-15 01:54:21下载
- 积分：1
-
matlab
从初值出发，先计算y对时间t的导数，得到y的变化速度；求出x对t的导数，得到x随时间的变化速度。然后时间前进一小步h=0.002，同时x和y也都发生一个小的变化，即在原来数值基础上加上时间步长h和变化速度的乘积。如果x到达1或者-1，强制让y发生变化。这个过程不断迭代，得到结果。
(completed chart)
- 2014-11-28 19:50:30下载
- 积分：1
