-
小波降噪与EMD混合
一种进行小波降噪后，对特征库的信号进行信号经验模态分解的例子(An example of signal empirical mode decomposition for signal of characteristic library after wavelet de-noising)
- 2017-06-05 00:06:21下载
- 积分：1
-
01
说明： 这里提供了一个求最短路径的MATLAB算法，大家可以参考以下(Here provides a shortest path for the MATLAB algorithm, we can refer to the following)
- 2007-10-27 19:39:31下载
- 积分：1
-
dianfengshan
matlab动态模拟程序例子，小电风扇，是学习matlab的很好实例。(Dynamic simulation program matlab example, a small fan, is a good example to learn matlab.)
- 2013-11-03 16:04:22下载
- 积分：1
-
Factor-analysis
因子分析。该程序已经调试好了 直接可以使用(Factor analysis. The program has a good debugging can be used directly)
- 2013-04-02 14:25:35下载
- 积分：1
-
matlab--implementation
matlab 的安装实现，帮助大家成功的实现matlab的安装。(Hadoop installation implementation, to help you successfully hadoop installation.
)
- 2013-10-03 11:56:41下载
- 积分：1
-
ofdm
OFDM channel Using a large number of parallel narrow-band subcarriers instead of a single wide-band carrier to transport information
l Advantages
» Very easy and efficient in dealing with multi-path
» Robust again narrow-band interference
- 2015-04-10 17:09:57下载
- 积分：1
-
Matlab编的计算器
本程序是在Matlab6.5下编写的一个计算器的程序，是Matlab的GUI编程的很好例子。 (the procedure was Matlab6.5 prepared a calculator procedures, Matlab GUI Programming good example.)
- 2005-06-04 09:32:05下载
- 积分：1
-
ds
说明： MATLAB中用遗传算法求解约束非线性规划问题(MATLAB using the genetic algorithm for solving constrained nonlinear programming problem)
- 2009-08-17 18:15:27下载
- 积分：1
-
idealCentre20150304
一个房地产项目微官网源码，动态效果不错，自适应各种手机屏幕(A real estate project micro website source code, dynamic effect is good, the adaptive to various mobile phone screen)
- 2015-03-23 14:37:57下载
- 积分：1
-
grd_test
xwch_test.m是主测试文件；biaoji.mat存放滤波器系数；xiangweicha.m用FFT计算相位差。
仿真框架为：
1.标记信号和双音信号续接作为发送信号；
2.对双音中一个频率分量的相位做偏移，再经过一个低通滤波器（引入线性相位，模拟收发不能同步测量现象）后，作为收到的信号；
3.用一个检测信号对收发信号进行相关运算；
4.画出收发信号以及相关处理后的信号。找出相关信号的那个尖点，从而推算出收发双音信号0相位点；
5. 输入0相位点位置，计算相对相位差。(xwch_test.m is the main test file biaoji.mat store filter coefficients xiangweicha.m calculated using FFT phase difference. Simulation framework: 1. Mark signals and then as a two-tone signal continued to send signals 2. On a two-tone frequency components of the phase shift to do, and then through a low pass filter (the introduction of linear phase, simulation can not simultaneously send and receive measuring the phenomenon), the as received signal 3. using a detection signal of the transceiver signal correlation operation 4. draw send and receive signals and related processed signal. Correlated signal of the cusp, which calculate the two-tone signal transceiver 0 phase point 5. Enter 0 phase point position, calculate the relative phase difference.)
- 2010-06-12 17:31:00下载
- 积分：1
