-
瞬态动力学分析
说明： 三个ANSYS瞬态分析的命令流：冲击载荷作用悬臂梁的阻尼振动分析；破碎锤的瞬态动力学分析；滑动摩擦接触分析(Three command streams of ANSYS transient analysis: damped vibration analysis of cantilever beam under impact load; transient dynamic analysis of crushing hammer; sliding friction contact analysis)
- 2020-06-16 19:20:01下载
- 积分：1
-
matlab TOA and TODA local
说明： 利用TOA与最小二乘法直接求解（具有独立创新性），TDOA是利用拉格朗日法求解，而且里面的定位图解做得特别好，分别有一点定位，多点定位的的三维视觉图。(TOA is directly solved by least squares method(Innovativeness),TDOA is solved by Lagrange's method.)
- 2021-04-06 20:49:02下载
- 积分：1
-
UPFC模型
说明： UPFC模型，模型非常详细和系统，有助于理解潮流控制器(UPFC model, which is very detailed and systematic, helps to understand power flow controllers)
- 2019-04-22 18:56:05下载
- 积分：1
-
双馈风机并网
说明： 双馈风机变速仿真：
电压/无功控制下机组输出仿真；
电压/无功电网故障下输出仿真(Doubly-fed fan variable speed simulation:
Unit output simulation under voltage / reactive power control;
Output simulation under voltage / reactive grid faults)
- 2020-03-16 19:14:58下载
- 积分：1
-
umat
说明： 用于abaqus里形状记忆合金材性模拟的子程序umat文件(an umat file used to simulate SMA in ABAQUS)
- 2021-01-15 21:58:45下载
- 积分：1
-
系统辨识及其MATLAB仿真
对动态系统辨识理论做了概括性的介绍，包含了常用的非参数系统辨识方法和参数辨识方法，并将神经网络人工智能算法应用到复杂系统参数识别，适用于系统控制、参数识别与数据预测等领域的学习。传统方法与现在智能算法都配有实例，每个代码文件都有详细注释。(This paper gives a general introduction to the dynamic system identification theory, including commonly used non-parametric system identification methods and parameter identification methods, and applies neural network artificial intelligence algorithms to complex system parameter identification, which is suitable for system control, parameter identification and data prediction. Learning in other fields. Both traditional methods and current smart algorithms are equipped with examples, and each code file has detailed comments.)
- 2018-12-18 13:55:29下载
- 积分：1
-
新建文件夹
说明： 运用卡尔曼滤波器，在已有条件下，用matlab软件得到与已知的飞行器轨迹相同的预测轨迹(Kalman filter is used to predict the flight path of the aircraft)
- 2020-12-13 12:20:22下载
- 积分：1
-
original
逆流套管式换热器仿真小程序，工质物性调用refprop,所以需要自行嵌套refprop(Counter flow sleeve heat exchanger simulation small program, physical properties call RefProp, so need to self nest RefProp)
- 2018-10-04 11:28:41下载
- 积分：1
-
power_statcom
用matlab动态无功补偿器statcom的仿真模型(Dynamic reactive power compensator statcom simulation mode)
- 2017-10-15 20:29:09下载
- 积分：1
-
kong
说明： 在 Carsim 中分别搭建好前车与后车的车辆纵向动力学
模型。雷达系统将探测到的后车信息和前车信息传递给行车
间距控制系统，此控制系统根据安全距离模型计算出后车车
辆期望加速度，此期望加速度经过 PID 控制器调节后，输入
给车辆动力学系统，车辆动力学系统基于此加速度输出期望
的制动压力和节气门开度，并将此值传给制动及节气门控制
系统，此系统输出相应的制动力及节气门开度给后车动力学
系统，进行制动及加速控制。(The vehicle longitudinal dynamics of the front car and the rear car were built respectively in Carsim
Model.The radar system transmits the information of the vehicle behind and the vehicle in front to the vehicle
Spacing control system, this control system according to the safe distance model to calculate the rear car
Vehicle expected acceleration, the expected acceleration after PID controller adjustment, input
Given to the vehicle dynamics system, the vehicle dynamics system is based on this acceleration output expectation
Brake pressure and throttle opening, and pass this value to brake and throttle control
System, which outputs the corresponding braking force and throttle opening to the rear car dynamics
System for braking and acceleration control.)
- 2021-03-19 11:09:19下载
- 积分：1
