登录
首页 » matlab » 光储一体化发电系统的控制

光储一体化发电系统的控制

于 2021-04-22 发布
0 390
下载积分: 1 下载次数: 42

代码说明:

说明:  光储一体化发电系统的控制,采用电压电流双环控制(Double-loop voltage and current control is adopted in the control of integrated optical storage power generation system)

文件列表:

pv_3xiang_pqcontrol20170214_2.mdl, 197057 , 2019-04-14

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • lliangdianfa
    说明:  通过两点法 计算水波的反射系数 海洋工程领域实用代码(The reflection coefficient calculation by two points method. Useful code for ocean engineering.)
    2021-04-06 10:19:02下载
    积分:1
  • Lyapunov exponent (2)
    表示相空间相邻轨迹的平均指数发散率的数值特征。又称李雅普诺夫特征指数,是用于识别混沌运动若干数值的特征之一。(Denotes the numerical characteristics of the average exponential divergence of adjacent trajectories. Also known as the lyapunov characteristic index, is one of the characteristics used to identify some numerical values of chaotic motion.)
    2020-09-11 15:08:01下载
    积分:1
  • PLL
    说明:  基于光混频器和锁相环的零差相干通信仿真模块,可观察锁相动态过程(Simulation of Homodyne Coherent Communication Based on Optical Mixer and PLL)
    2019-05-14 13:37:46下载
    积分:1
  • 三极管放大电路设计
    说明:  三极管放大实验电路,包括固定偏置/分压偏置,需要根据一些参数确定所选用的电阻值,使得三极管工作在放大状态。本程序将电路设计设计成GUI模式,界面上只需要输入电路设计所需参数,根据相关理论推导,给出相关参数的理论值(放大倍数、输入电阻、输出电阻等),指导实验电路搭建。软件搭建在matlab gui上,方便使用 若干参数说明 beta:三极管放大倍数 Ic:集电极电流 Uce:期望CE间电压 UeCof:Re电阻上点电压与Ucc电压比值,一般0.1-0.2 IbCof:Ib上电流与流过Rb1、Rb2电流的比值,一般0.1 ShuntCe:是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
    2020-04-29 15:11:59下载
    积分:1
  • 赵海鸥Ls_Dyna书籍光盘
    说明:  LsDyna二次开发流程介绍及示例。umat42各向同性材料。(Introduction and example of secondary development process of LSDYNA)
    2020-04-14 10:46:27下载
    积分:1
  • Spotweld_2or3Layers_001
    将CATIA数据里面的2层和3层焊点,批量生成point点。(Two and three layers of solder joints in CATIA data are generated in batches.)
    2020-06-17 21:40:01下载
    积分:1
  • 9035475
    Juli - 6,0,16 Java implementation of point to point short message sending agreement (SMPP) development kit source code(Juli- 6,0,16 Java implementation of point to point short message sending agreement (SMPP) development kit source code)
    2017-04-17 04:37:14下载
    积分:1
  • CH341PAR drivers
    CH341A USB Programmer v.1.30 Drivers
    2018-03-11 22:52:23下载
    积分:1
  • EMD
    说明:  轴承故障诊断,自己编写的基础EMD分解程序,实测很好用。(Bearing fault diagnosis, self-compiled basic EMD decomposition program, the actual measurement is very useful.)
    2021-04-11 13:28:57下载
    积分:1
  • 离散点生成等高线的程序 MyDTM
    离散点生成等高线的程序,基于方格网数字地形模型(Discrete points of the program to generate contour lines, grid-based DTM)
    2009-04-11 17:11:32下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载