-
pdftoolbox_cmd_win
说明： Command line PDF toolbox, fully registered version. Can work together with FOXIT Reader
- 2020-06-25 01:00:01下载
- 积分：1
-
mod
该MATLAB仿真程序适用于蓄电池的充电以及放电控制(The MATLAB simulation program is suitable for battery charging and discharge control.)
- 2018-04-19 15:58:36下载
- 积分：1
-
相位屏仿真方法
说明： matlab生成一个随机相位屏，可以模拟大气和电离层，结果为彩色图。(Matlab generates a random phase screen, which can simulate the atmosphere and the ionosphere. The result is a color map.)
- 2019-06-21 09:40:46下载
- 积分：1
-
三极管放大电路设计
说明： 三极管放大实验电路，包括固定偏置/分压偏置，需要根据一些参数确定所选用的电阻值，使得三极管工作在放大状态。本程序将电路设计设计成GUI模式，界面上只需要输入电路设计所需参数，根据相关理论推导，给出相关参数的理论值（放大倍数、输入电阻、输出电阻等），指导实验电路搭建。软件搭建在matlab gui上，方便使用
若干参数说明
beta：三极管放大倍数
Ic：集电极电流
Uce：期望CE间电压
UeCof：Re电阻上点电压与Ucc电压比值，一般0.1-0.2
IbCof：Ib上电流与流过Rb1、Rb2电流的比值，一般0.1
ShuntCe：是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
- 2020-04-29 15:11:59下载
- 积分：1
-
spwm-based
说明： 对电机进行基于spwm的变频调速系统，来实现对异步交流电动机的转速调整与三相电流调整(SPWM-based variable frequency speed regulation system for motor)
- 2019-04-29 14:27:57下载
- 积分：1
-
2d-FDTD
二维FDTD程序，以方柱为例仿真其散射的波形(Two-dimensional FDTD procedures for square cylinder as an example simulation of the scattering wave)
- 2008-05-12 22:20:05下载
- 积分：1
-
WinFOF_SRC
Selfscanning codes for seagate hdd
- 2021-01-15 17:38:45下载
- 积分：1
-
windfarm
基于PSCAD4.5的双馈感应式风力发电系统仿真，矢量控制(Simulation of doubly fed induction wind power generation system based on PSCAD4.5 and vector control)
- 2018-11-02 11:20:50下载
- 积分：1
-
悬架LQG控制
使用MATLAB/simulink创建悬架模型，设计LQG最优控制器，进行汽车主动悬架最优控制。(The suspension model is created by using MATLAB/simulink, and the LQG optimal controller is designed to optimize the vehicle active suspension.)
- 2020-12-16 10:19:12下载
- 积分：1
-
gkdnzdpfxt
说明： 高考电脑自动评分系统是很多同学选择的毕业设计,希望能有帮助(GKDNZDPFXT)
- 2010-03-23 21:30:20下载
- 积分：1
