-
LabView-PID-Incremental
LabView编程环境下PID增量式算法（已实验通过，放心下载）(PID Incremental Algorithm In LabView)
- 2020-08-14 16:28:35下载
- 积分：1
-
6.2气象站
说明： 使用labview进行设计，里面内含粉尘采集，气压采集，温度采集，适度采集等子程序及其集合(Design with LabVIEW, which contains dust collection, air pressure collection, temperature collection, moderate collection and other subroutines and their collection)
- 2020-04-25 11:37:03下载
- 积分：1
-
Super_XYGraph
说明： labview中常常需要显示曲线，并需要制作缩放，设置，浮动游标等功能。本Xcontrol集成了这些功能，这样就不用每次都去写麻烦的曲线操作了！(LabVIEW often needs to display the curve, and needs to make zoom, set, floating cursor and other functions. This XControl integrates these functions, so you don't have to write troublesome curve operations every time!)
- 2020-08-24 14:03:31下载
- 积分：1
-
Fibonacci
裴波拉那齐数列前一百项求和，利用while循环等(Pei Qi sequence that summed Bora Fibonacci)
- 2014-02-18 12:09:59下载
- 积分：1
-
Acouostic-Signal-Test01
声学系统测试，生成impulse noise 和non-Gaussian noise混和信号(Acoustic system testing, generate impulse noise and non-Gaussian noise mixed signals)
- 2014-04-10 23:45:38下载
- 积分：1
-
shudu
数独labview实现的源代码,辛苦写出来的(shudu labview source)
- 2021-01-22 19:38:45下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
说明： 基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
Noise-detection
用Labview分析笔记本采集到的噪声信号频率计权声级(Using Labview analysis laptop to noise signal frequency meter right sound level)
- 2013-09-21 14:06:31下载
- 积分：1
-
CRC-pudn
CRC16的9个LabVIEW算法CCITT,CCITT-KERMIT,CCITT-X25，CCITT-XMODEM,DNP,IBM,MAXIM,MODBUS,USB，开发环境LabVIEW2013(9 LabVIEW algorithm of CRC16: CCITT,CCITT-KERMIT,CCITT-X25，CCITT-XMODEM,DNP,IBM,MAXIM,MODBUS,USB The development environment version is LabVIEW 2013)
- 2020-12-03 11:29:25下载
- 积分：1
-
sound-source_positioning
基于labview的声源定位，利用广义互相关法求声音信号到麦克风阵列的时间差，然后根据麦克风阵列的距离阵型求得声源的位置(Sound Source Localization Based labview, the use of generalized cross correlation method the sound signal to the time difference between the microphone array, and then formation determined according to the location of the sound source the microphone array )
- 2017-01-11 17:18:55下载
- 积分：1
