登录
首页 » Python » cohesive

cohesive

于 2020-06-19 发布
0 300
下载积分: 1 下载次数: 19

代码说明:

说明:  用于abaqus建模内聚力单元建模,通过内聚力单元分析材料损伤(Used for abaqus modeling, the cohesion unit is used to analyze material damage)

文件列表:

cohesive.py, 11177 , 2016-08-29

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Digita188318512005
    Windows API/Global Declarations for :[ Digital Clock v1.0 ]
    2018-07-02 14:13:30下载
    积分:1
  • RC
    说明:  形成低通滤波器及实际RC低通滤波电路的单位冲激响应与频谱图(Unit impulse response and frequency spectrum of low pass filter and practical RC low pass filter circuit)
    2018-11-08 21:59:02下载
    积分:1
  • MATLAB计算DNL和INL
    MATLAB计算AD指标DNL等的程序,可参考(MATLAB calculation, AD indicators, DNL and other procedures, you can refer to)
    2021-04-24 20:08:46下载
    积分:1
  • 各工况测试曲线参数
    说明:  车辆循环各种工况包括UDDS等,可用于车辆各种仿真(Various working conditions of vehicle cycle)
    2021-02-19 10:45:38下载
    积分:1
  • ajyynfxz
    maven分模块项目+SSM宿舍管理系统+spring mvc+jquery+bootstrap+多模块+svn+分角色登录+分页+拦截器+收邮件。(maven????? + ssm?????? + spring mvc + + + jquery bootstrap ??? + svn + ????? + ?? + ??? + ???)
    2018-05-23 12:01:31下载
    积分:1
  • VMD
    采用可变模式分解对一维时间信号进行分解,其性能优于传统EMD,LMD等方法(signal processing method)
    2018-05-15 22:20:25下载
    积分:1
  • 某铁路大桥ANSYS建模命令流
    关于某大型斜拉桥建模命令流,可以作为铁路斜拉桥ansys建模参考(As for the modeling command flow of a large cable-stayed bridge, it can be used as a reference for ANSYS modeling of railway cable-stayed bridges)
    2021-03-19 12:49:19下载
    积分:1
  • weibull
    利用蒙特卡洛的方法进行威布尔参数估计,随机生成对应参数估计值,不断迭代达到需要精度(Weibull parameter estimation using Monte Carlo method.)
    2018-04-14 19:18:46下载
    积分:1
  • 三极管放大电路设计
    说明:  三极管放大实验电路,包括固定偏置/分压偏置,需要根据一些参数确定所选用的电阻值,使得三极管工作在放大状态。本程序将电路设计设计成GUI模式,界面上只需要输入电路设计所需参数,根据相关理论推导,给出相关参数的理论值(放大倍数、输入电阻、输出电阻等),指导实验电路搭建。软件搭建在matlab gui上,方便使用 若干参数说明 beta:三极管放大倍数 Ic:集电极电流 Uce:期望CE间电压 UeCof:Re电阻上点电压与Ucc电压比值,一般0.1-0.2 IbCof:Ib上电流与流过Rb1、Rb2电流的比值,一般0.1 ShuntCe:是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
    2020-04-29 15:11:59下载
    积分:1
  • ov7620
    说明:  至今几十个经典项目详细的开发文档举例!!(The development of detailed project documentation classic example!!)
    2009-08-29 21:50:08下载
    积分:1
  • 696518资源总数
  • 105873会员总数
  • 12今日下载