-
softwareengineering4
软件工程基本课件4，快速入门。精品课程教案。详细讲解软件工程相关知识(The basic software engineering courseware 4, Getting Started. Courses lesson plans. Explain in detail the software engineering knowledge)
- 2014-04-24 17:25:09下载
- 积分：1
-
OPC-intruduction
Data Access Custom Interface Standard
Version 2.05A
- 2013-06-29 11:36:30下载
- 积分：1
-
Restorator
反编译的最佳软件,能够读取软件资源,同时还具有修改的功能(Decompile the best software that can read software resources, but also has a modified function)
- 2008-03-20 16:03:55下载
- 积分：1
-
Fuzzy-risk-assessment-of-water
基于模糊概率的水资源短缺风险评价，对水资源的定量分析理论支撑(Fuzzy risk assessment of the probability of water shortage)
- 2011-06-02 17:28:10下载
- 积分：1
-
EIP
Embedded image processing on TMS320C6000
Useful for programmists of embedded processors.
- 2009-11-17 02:55:38下载
- 积分：1
-
Q3VM-Specifications
The Q3VM is a virtual machine used by Quake III to run the game module. The VM is a sort of
sandbox to limit the damage a rogue or malicious QVM program can wreak. Though not perfect,
it certainly is much safer than full access to native machine language, which could otherwise
more easily allow the spread of viruses or the corruption of system resources. In addition, Q3VM
programs, similar to JVM s, are write-once run-on-many-platforms (at least for which a Q3VM
interpreter or compiler exists).
- 2012-05-05 09:29:02下载
- 积分：1
-
TG12864A
TG12864A引脚资料 (TG12864A pin information)
- 2009-04-21 21:32:27下载
- 积分：1
-
PD-Radar
PD雷达抗速度欺骗干扰的计算机仿真及应用说明(PD Radar )
- 2012-04-14 17:27:40下载
- 积分：1
-
optimize-
键是一种标准零件,通常用来实现轴与轮毂之间的周向固定以传递转矩，有的还能实现轴上零件的轴向固定或轴向滑动导向。在键连接设计时，间的高度和宽度根据轴的直径d选取，而键长L则根据轴上零件轮毂宽度B而定，通常L=B-（5—10）mm。键的尺寸确定后，再进行强度校核。而为了保证绝对安全，键的尺寸取值往往都趋于保守，所选键的尺寸大。本程序采用优化设计方法，在满足强度要求的前提下求出键的最小结构尺寸，证明键宽b和键高h的取值可以小于标准值。(Key is a standard part, often used to achieve between shaft and hub to transfer torque to a fixed week, and some can achieve a fixed axis or axial parts of the axial sliding direction. Key connection in the design, height and width between the shaft diameter d according to selection, and the bond length L is based on the width of the wheel shaft parts B and, typically L = B-(5-10) mm. Key size is confirmed, then strength check. In order to guarantee absolute security, key size values ??are often conservative, the size of the selected key to big. The program uses optimization methods to meet the strength requirements of the derived key premise of the minimum structure size, proved key width b and height h of the key values ??can be less than the standard value.)
- 2011-09-05 20:16:03下载
- 积分：1
-
LC
LC滤波电路设计文档 一本非常好的书籍 很清晰易懂(LC DESIGN)
- 2013-11-20 12:37:14下载
- 积分：1
