-
文档与程序
这个是信号与处理专业的大作业,主要研究两个方面的问题:低通滤波器的阶跃响应特性分析和连续线性系统的求解。通过这次课程设计,将会研究Matlab的一些基本的数值计算应用方法,对计算结果进行形象化地展示,有利于加深对本课程内容的理解。(This is a major task of signal and processing specialty. It mainly studies two aspects: step response characteristic analysis of low-pass filter and solution of continuous linear system. Through this course design, we will study some basic numerical calculation application methods of MATLAB, and visualize the calculation results, which is conducive to deepening the understanding of the course content.)
- 2020-06-21 05:20:01下载
- 积分:1
-
Fluent-DPM
说明: 在fluent仿真软件中定义DPM两相流计算(Fluent user defined DPM Model)
- 2019-11-25 21:55:17下载
- 积分:1
-
文件
说明: 混响器的MATLAB实现:利用MATLAB/SIMULINK软件实现混响器(Realization of reverberator with MATLAB)
- 2020-03-25 17:42:37下载
- 积分:1
-
EKF_SOC
估算锂电池soc的MATLAB simulink模型(MATLAB Simulink model for estimating SOC of lithium battery)
- 2018-05-14 21:09:31下载
- 积分:1
-
弾流润滑
求解线接触弾流润滑中的压力与膜厚分布,包括雷诺方程、膜厚方程。变性方程、粘压方程以及密压方程的求解。(Solution of pressure and film thickness distribution in line contact lubrication)
- 2018-10-18 19:17:41下载
- 积分:1
-
清洁机器人路径规划matlab仿真程序
清洁机器人内螺旋算法仿真matlab程序,采用内螺旋算法全覆盖算法(Internal helix algorithm simulation)
- 2021-04-09 15:28:59下载
- 积分:1
-
求解一维LAVAL管亚音速流动
说明: 用MACCORMACK方法求解一维LAVAL管亚音速流动(solve one dimensional laval tube with the method in maccormack)
- 2020-05-28 10:47:49下载
- 积分:1
-
lead acid battery
说明: 能够实现充电仿真,具有电压电流反馈,能够实时观测蓄电池soc等参数(It can realize charging simulation, has voltage and current feedback, and can observe battery SOC and other parameters in real time)
- 2021-02-15 15:09:32下载
- 积分:1
-
CSR_PWM_x8
基于空间矢量的电流型整流器,双闭环,可运行,实现了电压电流同相位功能(The current mode rectifier based on space vector can operate with double closed loops, and achieve the function of voltage current and phase.)
- 2018-04-13 17:12:59下载
- 积分:1
-
usermat_CDM
说明: These composite materials generally exhibit brittle damage behavior. The anisotropy in the
material and different kinds of failure mechanisms make it difficult to accurately
characterize the behavior of composite materials. The present work aims to verify and
apply the Puck Failure Criteria using the commercially available finite element package
ANSYS by writing a user-material subroutine in FORTRAN. The model is implemented
with different post failure degradation schemes EWM/CSE.
- 2019-05-01 00:48:50下载
- 积分:1