-
OFDM_tutorial
A comprehensive OFDM turorial
- 2010-07-04 01:53:58下载
- 积分：1
-
wavTransform
将wav文件从十进制转换成二进制，再从二进制转换回去(tansform a wav file from decimal to binary and reverse the process)
- 2012-05-24 17:27:00下载
- 积分：1
-
zishiyinglvbo
labviewz中自适应滤波算法之调用MATLAB的相关程序。(Adaptive filtering algorithm Calling MATLAB program.)
- 2013-05-20 15:56:44下载
- 积分：1
-
TIac
TI公司的交流电机控制仿真的Matlab程序,很有用的啊,大家快下吧(AC motor control simulation of the Matlab program, very useful ah, everyone under the bar fast)
- 2009-11-10 13:05:35下载
- 积分：1
-
Verify-sampling-theorem
说明： 用于验证时域采样定理，进一步理解和使用采样定理(Used to verify the time-domain sampling theorem
)
- 2011-03-02 23:24:55下载
- 积分：1
-
chengxu
灰色预测对于房价走势的预测，分析了个元素对于房价的(It is very useful)
- 2011-09-28 03:28:12下载
- 积分：1
-
S11-IEEE-IEC-ComparisonDocument
Comparison of IEEE and IEC Grounding methods
- 2014-02-03 22:22:03下载
- 积分：1
-
fstb
FISMAT accommodates different arithmetic operators, fuzzification and defuzzification algorithm, implication relations, and different method of approximate reasoning such as Compositional Rule of Inference (CRI) and Approximate Analogical Reasoning Scheme based on Similarity Measure.
- 2005-07-26 15:55:59下载
- 积分：1
-
swept-sine-vibration
基于ANSYS APDL二次开发的航电设备的动力学扫频分析，载荷输入条件为交越频率以下为恒定位移，交越频率以上为恒定加速度。我将加速度输入转换为位移输入，将位移和加速度两段输入载荷统一按照位移载荷输入，将位移存入表数组，利用ANSYS APDL自动将扫频范围内的位移载荷存入表数组，并循环加载计算，实现了该工程结构的正弦扫频振动分析。(Kinetic sweep analysis, load input conditions of secondary development based on ANSYS APDL avionics for the crossover frequency less constant displacement, above the crossover frequency is constant acceleration. I will convert the input displacement input acceleration, displacement and acceleration loads unity in accordance with the displacement of the two input load input, the displacement of the array into the table using ANSYS APDL automatically load displacement within the sweep range of the array into the table, and cyclic loading calculated to achieve a swept sine vibration of the project structure.)
- 2013-12-02 13:48:03下载
- 积分：1
-
Blind-identification
利用现代谱估计中的AR 模型求取仿真噪声信号和真实噪声信号的模型参数，然后利用这些参数求得信号的功率谱图，通过功率谱图定性地描述主噪声源和次噪声源。在利用信号功率谱图定性描述噪声源后，进一步地利用曲线相似度和曲线关联度定量的识别主噪声源和次噪声源(Use of modern spectral estimation of AR model to strike a realistic simulation of the noise signal and noise model parameters, and then use these parameters obtained by the signal power spectrum, power spectrum qualitatively described by the main noise source and the second noise source. In the use of qualitative description of the noise signal power spectrum of the source, the further use of the correlation curve and the curve of quantitative similarity identification of the main noise source and the second noise source)
- 2011-11-20 22:07:43下载
- 积分：1
