登录
首页 » matlab » oneuntitled

oneuntitled

于 2021-01-23 发布
0 271
下载积分: 1 下载次数: 23

代码说明:

说明:  利用MATLAB/Simulink搭建的三电平逆变器仿真电路,利用模型预测控制方法进行控制,可以实现中点点位平衡,对研究模型预测控制有一定学习作用。(The simulation circuit of three-level inverter built by MATLAB/Simulink and the control by model predictive control method can realize the balance of mid-point and point, which has a certain learning effect on the study of model predictive control.)

文件列表:

oneuntitled.slx, 44995 , 2019-08-28

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • SHT30
    调试ok,sht30温湿度传感器,基于stm32平台(Debugging OK, sht30 temperature and humidity sensor, based on STM32 platform)
    2021-02-02 23:09:59下载
    积分:1
  • 三极管放大电路设计
    说明:  三极管放大实验电路,包括固定偏置/分压偏置,需要根据一些参数确定所选用的电阻值,使得三极管工作在放大状态。本程序将电路设计设计成GUI模式,界面上只需要输入电路设计所需参数,根据相关理论推导,给出相关参数的理论值(放大倍数、输入电阻、输出电阻等),指导实验电路搭建。软件搭建在matlab gui上,方便使用 若干参数说明 beta:三极管放大倍数 Ic:集电极电流 Uce:期望CE间电压 UeCof:Re电阻上点电压与Ucc电压比值,一般0.1-0.2 IbCof:Ib上电流与流过Rb1、Rb2电流的比值,一般0.1 ShuntCe:是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
    2020-04-29 15:11:59下载
    积分:1
  • ecms_QD_49T_1
    并联式混合动力汽车等效燃油消耗最小m程序,瞬时最优(ECMS code for Parallel hybrid vehicle)
    2021-03-30 23:09:09下载
    积分:1
  • GPS
    卫星轨道仿真,基于广播星历下的GPS卫星轨道仿真(Satellite orbit simulation)
    2020-11-13 15:19:43下载
    积分:1
  • Arx1
    说明:  选取四个点,自动判断是否在一个平面上。同一个平面上。则绘制一个多边形。不在一个平面,则以前三个点为底面,构成一个椎体。支持Move等转换命令,存图与开图,实现Jig交互绘制等。(Four points are selected to automatically determine whether or not they are on a plane. On the same plane. Draw a polygon. If it is not in a plane, the first three points are at the bottom, forming a vertebral body. Support Move and other conversion commands, save and open maps, Jig interactive rendering, etc.)
    2020-06-16 08:40:02下载
    积分:1
  • DY1
    MATLAB模型,是永磁同步发电机根据转矩不同发出的不同功率,通过仿真,可以方便的分析,永磁同步发电机输出功率。(MATLAB model is the power of permanent magnet synchronous generator according to different torque. Through simulation, it is convenient to analyze the output power of permanent magnet synchronous generator.)
    2017-09-19 17:19:01下载
    积分:1
  • rad_dms
    实现弧度向角度的转换,判断在第几象限。。。。。。(Realize the conversion of radian to angle and judge the quadrant)
    2019-01-13 19:12:24下载
    积分:1
  • NX Open C++ 9.0
    nxopen c++二次开发帮助文档,函数查找手册(Nxopen C + + secondary development help document)
    2021-03-12 15:59:25下载
    积分:1
  • Encode5b_4b
    PD里面的4B5B编码,欢迎使用~~~~~~~~~~~~~~~~~(4B5B code in PD3.0 or USB3.0, welcome to use~~~~~~~~~~~~~~)
    2020-12-03 09:09:25下载
    积分:1
  • nec_bldc_ver1_IDC_FD_whole_07911
    说明:  启航电动自行车控制器软件,已经量产。用于替换晶汇控制器。(BLDC controller for elec-bike)
    2019-01-19 21:16:31下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载