-
IEEE14ChaoLiuZS
说明： IEEE14节点潮流计算程序。程序最初的数据模块可以修改成别的，如IEEE30节点和57节点的等等，矩阵取名用的是中文拼音(IEEE14 node flow calculation program)
- 2010-04-18 15:01:31下载
- 积分：1
-
Cap03_Coverage-
无线信道建模很复杂，不同场景下的模型差异较大，这是一本讲解无线信道建模方法的经典书籍配套的matlab例程(Channel modeling is complex models under different scenarios are quite different, which is a classic way to explain the channel modeling books matching matlab routines)
- 2013-09-13 09:47:18下载
- 积分：1
-
DSP_3_17_1
产生随机信号观测样本，不同信噪比和归一化频率。利用基于FFT的自相关函数快速计算方法估计其自相关函数。(Generate random signal observation samples, different signal to noise ratio and normalized frequency.Based on FFT calculation method of the autocorrelation function to quickly estimate the autocorrelation function.)
- 2015-04-10 17:03:22下载
- 积分：1
-
matlab
matlab程序资料请大家指教，辛苦大家啦(matlab program information, please advise, hard everyone!)
- 2012-07-13 09:35:51下载
- 积分：1
-
sift
sift 特征提取算法matlab实现,有实例(sift 特征提取算法matlab实现，有实例)
- 2020-07-21 14:48:46下载
- 积分：1
-
2D_EMD_Codes
二维经验模态分解，采用形态学求极值点，径向基神经网络拟合，速度较快。(Two-dimensional empirical mode decomposition, the use of morphology for extreme points, Radial Basis Function Neural Network Fitting, faster.)
- 2007-07-15 14:31:45下载
- 积分：1
-
MR_PET_ronghe
基于小波的脑部MR与伪彩色PET医学图像融合，低频采用加权平均，高频采用3*3区域标准差的融合规则，效果很好，内含一组脑部MR与PET医学图像(Simulation Wavelet-based for brain PET and MR image fusion, low frequency using the weighted average and high frequency using region-based standard deviation fusion rule, the effect is very good, including a set of MR and PET images)
- 2021-03-03 21:29:34下载
- 积分：1
-
degtodms
degtodms
function in matlab
geomatic students
matlab code
- 2014-10-26 01:41:59下载
- 积分：1
-
LDPCcode
利用函数MadHG生成规则LDPC码的校验矩阵H，其行重为6,列重为3,行数为列数一半(行数越大越好)，H中任意两列没有围长为4的圈，并得到H对应的生成矩阵G，可以保证mod(G*H ,2)=0。使用方法为:[H,G] = MadHG(m,n,x),x= 1(得到的G左半部分为单位阵) or 2(G右半部分为单位阵),(use function MadHG Generation rules LDPC check matrix H, re-6, series of three, out for a few half of the number (A bigger the better), H 2 arbitrary no girth of the four circles, H counterparts and with the formation of matrix G, we can be assured of mod (G* H, 2) = 0. To be used : [H, G] = MadHG (m, n, x), x = 1 (the G part of the Left Front units) or 2 (G right half of the units RUF),)
- 2007-05-12 10:49:48下载
- 积分：1
-
Matlab-Basic-Tutorial
Matlab基础及其应用教程，系统介绍Matlab工具如何使用(Matlab Basic Tutorial)
- 2011-07-20 15:51:08下载
- 积分：1
