-
BP2神经网络
说明： 通过labview对BP神经网络进行训练，得到BP模型。(The BP neural network is trained by labview to obtain the BP model.)
- 2019-10-01 20:47:49下载
- 积分：1
-
快速FFT变换
利用labview软件编写程序对信号进行快速傅里叶变换(Fast Fourier transform of signal is programmed by LabVIEW software.)
- 2018-05-22 20:12:15下载
- 积分：1
-
Full Samplings
说明： Scripts for up sampling and down sampling
- 2021-03-09 05:41:25下载
- 积分：1
-
USB上位机
说明： labviewUSB测试上位机程序，用于测试上位机与usb设备之间的通讯。(labview USB master,LabVIEW USB test host computer program, used to test the communication between host computer and USB device.)
- 2020-06-21 09:00:01下载
- 积分：1
-
fashengqi
基于labview的虚拟波形发生器，能够实现正弦、余弦、锯齿波的产生(Labview-based virtual waveform generator, to achieve the sine, cosine, sawtooth generation)
- 2013-12-22 16:15:06下载
- 积分：1
-
DataSocket
基于LabVIEW的datasocket的双机远程数据通信(Dual Remote Data Communication based the LabVIEW datasocket,)
- 2012-08-05 12:27:47下载
- 积分：1
-
shudu
数独labview实现的源代码,辛苦写出来的(shudu labview source)
- 2021-01-22 19:38:45下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
Time-domain-analysis-system
本系统可做自动控制原理中的时域分析仿真实验，系统特性如下：
1：可选择仿真系统为一阶、二阶、任意阶
2：可选择信号源为正弦波、三角波、锯齿波、方波（可模拟阶跃信号），并可调节信号源频率、幅值、相位、偏移、方波占空比
3：可选择信号采样率及采样数
4：自动计算传递函数
5：自动计算时域响应参数（增益系数、上升时间、峰值、峰值时间、稳定时间、超调量）
6：波形图同时显示原始信号和响应信号
注：使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)
- 2013-05-12 11:53:34下载
- 积分：1
-
baoluojianbo
一个包络检波的Labview程序，可插入到大型得项目文件中去，便于信号的分析(An envelope detection Labview program can be inserted into a large project file to facilitate the analysis of the signal)
- 2017-03-21 20:11:28下载
- 积分：1
