-
Python
lottery exchange system
- 2018-10-01 18:47:59下载
- 积分：1
-
beamforming misic MVDR
说明： 通过常规波束形成，MISIC,MVDR，三种方法对目标测向，并且对比三种方法的优缺点(Through conventional beamforming, misic, MVDR, three methods for target direction finding, and compare the advantages and disadvantages of the three methods)
- 2020-01-03 10:37:30下载
- 积分：1
-
PageOffice_4.5.0.6_Java
在线office编辑，多人同时编辑，希望大家喜欢(Online office editors, many people edit at the same time, I hope you like it.)
- 2019-03-01 14:16:18下载
- 积分：1
-
CPqD-RouteFlow-3f406b9
RouteFlow控制器Python代码(SDN RouteFlow Controller)
- 2018-02-27 12:11:17下载
- 积分：1
-
smoke_test
简单实现烟雾检测，在本次所采用的简易方法中，采用的是基于背景差分法(Simple realization of smoke detection)
- 2018-05-11 11:14:14下载
- 积分：1
-
遗传算法案例分析及源代码
基于遗传算法的选址MATLAB代码，案例分析(Location based MATLAB code based on genetic algorithm)
- 2020-12-28 09:49:02下载
- 积分：1
-
（1）GPIO例程
NXP lpc1788开发板例程,亲自测试，时OK的(nxp 1788 gpio,it is successful!)
- 2017-09-11 10:38:02下载
- 积分：1
-
CH11-KEA128-SPI
1. 硬件接线
（1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6
（在“uart.h文件中宏定义）。
（2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定）
（3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1，
SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3，
SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5，
SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。
（4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。
用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring
(1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6.
(macro definition in the uart.h file).
(2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection.
(3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1.
The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3.
The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5.
The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7.
(4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption.
PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)
- 2020-06-16 12:00:01下载
- 积分：1
-
风速
说明： MATLAB 风速程序，可用于计算湍流度(MATLAB,The wind speed program can be used to calculate the turbulence intensity.)
- 2021-01-21 11:38:40下载
- 积分：1
-
Linear_reg
说明： 线性回归模型实现代码，用于实现线性回归，包括最小二乘，主成分分析(the code of linear regression model)
- 2020-06-24 09:54:50下载
- 积分：1
