登录
首页 » matlab » MATLAB-lapalce8778yuu

MATLAB-lapalce8778yuu

于 2010-09-28 发布 文件大小:689KB
0 160
下载积分: 1 下载次数: 2

代码说明:

  transformada de laplace codigos

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • equilibrium-point
    根据系统的动力学方程m文件和simulink求出系统的平衡点(Based on the system dynamics equation of m documents and simulink the equilibrium point of system)
    2013-06-01 20:58:27下载
    积分:1
  • VC_MATLAB
    VC++中使用MATLAB的C++数学库和MCC生成的程序(VC++ in the use of MATLAB' s C++ Math Library and MCC procedures generated)
    2009-04-26 22:53:50下载
    积分:1
  • 907846864ExcellRead
    用运matlab软件对excel进行批量读取(Yun matlab software with batch reading excel)
    2013-11-17 11:41:59下载
    积分:1
  • bilinear
    implementing the bilinear transformation
    2011-10-13 13:32:42下载
    积分:1
  • rakereceive_kron
    本程序仿真了AWGN信道下,采用DS扩频对bpsk信号的影响,扩频码采用walsh码,扩频因子16; 接收端进行rake接收,然后分集合并,比较了三种分集方式对误码率的影响 从图像可以看出在扩频因子较高的情况下,最大比值合并与等增益合并性能相近(This program simulates the AWGN channel, using DS spread spectrum signal for bpsk influence spreading code using walsh code spreading factor 16 Rake receiver receiving end, and diversity combining, diversity compares three methods on the bit error rate of As can be seen from the image in the case of higher spreading factor, the maximum ratio combining and equal gain combining similar performance)
    2013-08-31 18:29:24下载
    积分:1
  • algoritmos-de-ordenamiento
    ALGORITH OF ORDERS IMPLEMENTED IN C++
    2014-12-18 12:57:11下载
    积分:1
  • pll_frequencey_synthesis
    基于matlab中simulink的频率合成器的设计,主要结构包括鉴相器,低通滤波器,压控振荡器(simulink based franquence synthesis,consisted of pdf,lpf,vco)
    2009-05-24 22:05:17下载
    积分:1
  • voc-dpm-master
    可变形部件模型Deformable Part Models是目前最好的目标检测算法(Deformable component model Deformable Part Models is the best target detection algorithm)
    2014-08-29 20:23:07下载
    积分:1
  • Report_Proj5_jiangchen_10212020018
    设计一个程序,用后向Euler 法/梯形法求解电路系统的MNA 方程(该方程由stamp 程 序得到),其中线性方程的求解采用GCR 迭代法。(Design a program that uses the backward Euler method/trapezoid method for solving circuit system MNA equation (the equation obtained by the stamp program), in which the linear equations using GCR iteration.)
    2021-01-04 21:58:55下载
    积分:1
  • 9
    说明:  龚纯主编的“matlab语言常用算法程序集”的第九章源代码(Gong pure edited matlab language commonly used algorithm for assembly, &quot the ninth chapter of source code)
    2012-12-03 19:05:14下载
    积分:1
  • 696518资源总数
  • 105595会员总数
  • 1今日下载