-
bchgenpoly
产生BCH码多项式，其中码字长度为N，消息长度为K(BCH code generated polynomial, which codeword length N, message length K)
- 2007-07-16 17:31:18下载
- 积分：1
-
jianchuanzaoshengxinhao
一个舰船噪声信号仿真建模的程序，已经测试通过，并且可以实际应用，修改参数即可仿真各类特殊的信号(A ship noise signal simulation and modeling procedures have been tested, and practical application, modify the parameters to simulation of various types of special signal)
- 2012-06-27 14:29:45下载
- 积分：1
-
baoluofenxi
采用解调分析方法，从信号中提取调制信息，分析其强度和频次就可以判断研究对象（诸如机械零件）损伤的程度和部位。(Using the demodulation method, the modulation information is extracted from the signal, the strength and frequency analysis can determine the study (such as mechanical parts) and location of the degree of damage.)
- 2013-09-30 04:08:32下载
- 积分：1
-
gaijincandybianyuannjiancesuanfa
一种改进的canndy边缘检测算法，非常新颖，值得学习(An improved edge detection algorithm canndy, very novel, it is worth learning)
- 2014-11-30 21:40:12下载
- 积分：1
-
实验五：信号抽样与恢复
信号的抽样和恢复，若 是带限信号，带宽为 , 经采样后的频谱 就是将 的频谱 在频率轴上以采样频率 为间隔进行周期延拓。因此，当 时，不会发生频率混叠；而当 < 时将发生频率混叠。(The signal sampling and recovery)
- 2017-11-29 11:11:25下载
- 积分：1
-
4jiejunheng
说明： 修改控制策略扭矩分配模块，离合器改为转速控制(Modify the control strategy torque allocation module and change the clutch to speed control)
- 2019-01-21 18:59:49下载
- 积分：1
-
esprit
在均匀线阵阵列中采用esprit算法对信号的DOA进行估计的仿真程序(Bursts out in the uniform linear esprit algorithm used in signal DOA estimation of simulation program)
- 2008-07-31 20:52:12下载
- 积分：1
-
BP-PID
基于BP神经网络的PID参数自整定，实现PID控制器的自适应控制(Self-tuning of PID parameters based on BP neural network)
- 2017-07-09 09:33:29下载
- 积分：1
-
lld
lcd编程代码 lcd局部特征尺度分解局部特征尺度分解(LCD programming code)
- 2021-03-03 09:29:34下载
- 积分：1
-
AODV路由协议 MATLAB仿真
利用matlab实现无线自组织网AODV仿真的算法源码。 为由50个节点构成的网络。在50m×50m大小的区域内，随机的产生50个节点。由用户指定源节点和目的节点，程序负责给出从源节点到目的节点的最小路径和此路径的跳数。各个节点之间设定为只要在自己直接通信范围内的其它节点，均一跳可达。-Write your own realization of the use of matlab simulation of wireless self-organizing network algorithms AODV source. The grounds of a network of 50 nodes. Size of 50m × 50m in area, randomly generated 50 nodes. By the user to specify the source node and destination node, the program responsible for the given node from the source node to the destination path and this path is the minimum number of hops. Set between each node to communicate directly as long as within the scope of their other nodes, all jump up.
- 2022-06-13 19:59:20下载
- 积分：1
