-
NAND FLASH控制器
NAND FLASH的控制器，Micro的样例，MCU端口有用到wishbone总线（软硬Core均可以）
- 2023-01-25 13:45:04下载
- 积分：1
-
I2C_master_code
主要介绍，I2C总线主设备发送数据给从设备，代码实现是用Verilog语言实现的，对硬件设计者有很大好处(Introduces, I2C bus master to send data to the slave device, code is implemented in Verilog language, the hardware designer of great benefit)
- 2011-07-12 14:31:11下载
- 积分：1
-
daima
Rst是低电平有效的系统复位信号，Clk是时钟信号。AB[5：0]是地址信号，DB[7：0]是数据信号，wr是低电平有效的写信号。start是启动信号。
模块中有一个64x8的双端口的存储器。系统复位结束后，可以通过AB、DB和wr信号向同步存储器写入数据。当写入64个数据后，给出一个Clk周期宽度的脉冲信号start，则系统从存储器0地址处开始读出数据，读出的8位数据从低位开始以3位为一组，每个时钟周期输出一组，即第一个时钟周期输出[2：0]位，第二个时钟周期输出[5：3]位，第三个周期输出1地址的[0]位和0地址的[7：6]位，直至将存储器中64x8数据全部输出。若最后一组不足三位，则高位补0。
(Rst is an active-low system reset signal, Clk is a clock signal. AB [5: 0] is the address signal, DB [7: 0] is the data signal, wr write signal is active low. start is the start signal. Module in a dual port memory of 64x8. After the reset, you can write data to the synchronous memory by AB, DB and wr signals. When data is written to 64, given the width of a pulse signal Clk cycle start, the system begins to read the memory address 0, 8 data read out a low starting with three as a group, each clock outputs a set period, which is the first clock cycle of the output [2: 0] bits, the second clock cycle output [5: 3] position, the third cycle of the output of an address [0] and 0 address [7 : 6] bit, until all the data in memory 64x8 output. If the last group of less than three, the high 0s.)
- 2014-12-11 20:16:04下载
- 积分：1
-
AD_FIFO
简单的Verilog程序，针对音频实验板的AD到DA调通试验，下载执行前请按照自己试验环境更改设置(Simple Verilog program for test the AD to DA loop of universal audio test platform.
Please configure it according to the test environment before download and implement the program to FPGA)
- 2013-01-26 00:47:37下载
- 积分：1
-
D_flip
source vhdl code of D flipflop logic
- 2011-03-18 17:49:28下载
- 积分：1
-
CAN协议控制器的Verilog实现
说明： 基于FPGA的CAN总线控制器，VERILOGHDL源代码，Q2仿真实现。可用。(FPGA-based CAN Bus Controller, VERILOGHDL source code, Q2 Simulation. Available.)
- 2020-11-26 15:29:31下载
- 积分：1
-
volt_mea_disp
本程序是用verilog 编写的模块，用来在lcd1602上显示用tlc549采样的电压值(This program is written in verilog module, used in lcd1602 display with tlc549 sampled voltage value)
- 2013-07-26 00:58:35下载
- 积分：1
-
华为经典FPGA设计全套入门技巧
说明： 华为FPGA设计全套资料，学习FPGA的朋友可以下载看看。(Huawei FPGA design a full set of materials, friends learning FPGA can download and see.)
- 2019-04-02 13:54:48下载
- 积分：1
-
11bit_Barker_code
设计11位巴克码序列峰值检测器，巴克码相关器原理：巴克码相关器能够检测巴克码序列峰值，并且能够在1bits错误情况下检测巴克码序列峰值。(A 11-bit Barker code sequence peak detector is designed. The principle of Barker code correlator is that the Barker code correlator can detect the peak value of Barker code sequence and detect the peak value of Barker code sequence in the case of 1 bits error.)
- 2020-06-21 14:00:01下载
- 积分：1
-
ht66f0185-1
小家电常用芯片HT66F0185的UART 使用例子，已在产品使用(Small appliances commonly use UART chip HT66F0185 of example, has been used in products)
- 2020-10-09 16:27:34下载
- 积分：1
