-
AnalyseError
Analyse error of imgage.
- 2009-03-27 10:08:19下载
- 积分：1
-
spline3
三次样条插值，很不错的插值算法，值得参考(Cubic spline interpolation, the interpolation algorithm is pretty good, it is also useful)
- 2021-01-19 18:08:42下载
- 积分：1
-
ofdm_simu
OFDM系统仿真，信号采用卷积编码和交织技术、采用16-QAM和QPSK两种调制方式，干扰分别采用多径衰落和瑞利衰落两种。(OFDM system simulation, signal the use of convolutional coding and intertwined technology, using 16-QAM and QPSK modulation in two ways, interference were used to multipath fading and Rayleigh fading two.)
- 2009-01-16 11:49:28下载
- 积分：1
-
mixtureBNT
上传-混合高斯贝叶斯网络分类器，有数据可以直接运行，互相交流，互相学习。(Upload- Gaussian mixture Bayesian network classifier, the data can be directly run, exchange, learn from each other.)
- 2010-09-07 19:51:20下载
- 积分：1
-
LBF
说明： 这是“Implicit Active Contours Driven by Local Binary Fitting Energy”（简称LBF模型）的MATLAB源代码。LBF模型是非常重要局部区域活动轮廓模型，它被广泛使用于各个领域，如MRI大脑图像分割，血管图像分割，图像偏差场纠正。(This is the "Implicit Active Contours Driven by Local Binary Fitting Energy" (referred to as the LBF model) of the MATLAB source code. LBF model is very important to local area active contour model, which is widely used in various fields, such as MRI brain image segmentation, vessel segmentation, image bias field correction.)
- 2021-04-16 10:58:53下载
- 积分：1
-
pvsystem
光伏发电系统，可用于新能源发电系统的研究设计 (PV systems)
- 2020-11-26 16:09:32下载
- 积分：1
-
毕设总程序
说明： 使用Harris角点检测器查找特征。再使用SIFT描述符并匹配两个图像之间的特征描述符。使用RANSAC执行单应。最后把图像包起来缝合。(Use Harris corner detector to find features. Sift descriptors are then used to match the feature descriptors between the two images. Use RANSAC to perform single response. Finally, the image is wrapped and stitched.)
- 2020-05-08 16:04:04下载
- 积分：1
-
代码汇总
说明： 实现了克里金插值，完美滴可以对比普通克里金和泛克里金(The Kriging interpolation is realized, and the perfect droplet can compare ordinary Kriging with Pan-Kriging.)
- 2020-11-16 21:39:41下载
- 积分：1
-
faultlocation_lxn1
基于分布参数模型的比相式单相故障单端测距算法
关键词：输电线路；单端故障测距；分布参数：比相；ArP
仿真(Distributed parameter model based on single-phase than with single-ended fault location algorithm Key words: transmission line single-ended fault location distribution parameters: ratio of phase ArP Simulation)
- 2010-07-15 13:04:27下载
- 积分：1
-
BPNN4_2
load training.txt load TrainOut.txt
load validation.txt load ValOut.txt
load testing.txt load TestOut.txt
INPUT=[training validation testing]
OUTPUT=[TrainOut ValOut TestOut]
net=newff(INPUT,OUTPUT,200,{ tansig , purelin }, trainlm )
- 2010-04-18 21:42:58下载
- 积分：1
