登录
首页 » Matlab » 自适应控制算法源程序

自适应控制算法源程序

于 2022-03-13 发布 文件大小:5.81 kB
0 73
下载积分: 2 下载次数: 1

代码说明:

包含CV、CA、Single、当前、恒转弯速率、转弯模型,采用累计贡献率的方法,基于人工神经网络的常用数字信号调制,结合PCA的尺度不变特征变换(SIFT)算法,通过matlab代码,采用热核构造权重。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Matlab_fundamental_applied
    是MATLAB初学者的助手,介绍了MATLAB的窗口和命令,并有一些在通信方面的例子(MATLAB beginner' s assistant is introduced and the MATLAB command window, and there are some examples of communication)
    2009-05-19 16:02:21下载
    积分:1
  • m-matlab
    序列卷积的matlab源码,包括卷积结果输出等(Sequence convolution matlab source code, including the convolution results of the output, etc.)
    2009-12-15 10:11:06下载
    积分:1
  • ruilixindao
    锐利信道的matlab仿真源码和运行结果,文档内含两个源码,并有详细注释。(Sharp channel-source and run the matlab simulation results, the document containing the two-source, and detailed notes.)
    2009-06-08 17:53:51下载
    积分:1
  • caoyan
    基于汽车控制系统的系统辨识建模,基于汽车控制系统的系统辨识建模(Based on the auto control system identification system modeling)
    2012-04-09 15:46:49下载
    积分:1
  • serie furier use in signal processing
    傅立叶级数是一种特殊的工具,它允许任何周期信号(受某些条件限制)被分解成无限长的正弦曲线。这对许多人来说可能并不明显,但从数学和图形上都可以证明。实际上,这允许傅里叶级数的用户将周期信号理解为各种频率分量的和。
    2022-07-09 20:51:21下载
    积分:1
  • GUI_tips
    GUI_tips MATLAB GUI Tips Collated advice on construction of user interfaces by R. S. Schestowitz Imaging Science and Biomedical Engineering
    2011-01-15 20:04:37下载
    积分:1
  • fuzzy1
    模糊控制的程序,基于matlab工具箱,下载就能用,绝对正确(Fuzzy control program, based on the matlab toolbox, download you can use, absolutely correct)
    2011-06-09 15:58:24下载
    积分:1
  • phy1
    TD-HSPA+ 物理层的链路级仿真程序(TD-HSPA+ physical layer link level simulation program)
    2012-06-07 16:49:55下载
    积分:1
  • matlab
    matlab编程,100个实例,包括1-32 图形应用篇、33-66 界面设计篇、67-84 图形处理篇、85-100 数值分析篇。(matlab programming, 100 examples, including 1-32 graphical interface (Application) ,33-66 ,67-84 design articles graphic articles ,85-100 numerical analysis articles.)
    2011-09-05 18:04:20下载
    积分:1
  • HARQ
    利用matlab仿真了改进的二类选择重传HARQ机制的吞吐量与误比特率之间的关系。在仿真中对于编码和解码过程进行了简化:根据误比特率按概率模拟传输过程中码字的出错位数,在接收端只判断码字错误的位数是否在可纠错得范围之内。每发送一个码字,接收端根据出错位数信息检验其是否出错,没有出错则接收,否则要求重发,程序中利用alternate值交替发送信息码字和校验码字。当校验码字到来后,若校验码与原码组成的新码字能够纠错,则正确接收,否则要求重传。 (Retransmission the HARQ mechanism of throughput and bit error rate of the relationship between the use of matlab simulation improved second-class choice. In the simulation for the encoding and decoding process is simplified: digit of the code word of the error probability analog transmission process, according to the bit error rate of the receiving end only to determine the range of code word errors median whether error correction was. Each sending a code word, the information of the receiving end according to the error median test whether error, no error is received, or request retransmission, and the program using the alternate value alternately sent the information code word and the parity check code word. When the checksum word comes, if the new codeword able to check code with the original code error correction correctly received, otherwise require retransmission.)
    2013-04-10 10:36:20下载
    积分:1
  • 696518资源总数
  • 105958会员总数
  • 18今日下载