-
LabVIEW课设
虚拟仪器的网络控制 1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))
- 2020-12-23 18:09:07下载
- 积分：1
-
tcp编程 labview
内容：
LabVIEW_TCP网络通讯
简单点对点通讯举例_TCP Client
简单点对点通讯举例_TCP Server
交互式点对点通讯举例_TCP Client
交互式点对点通讯举例_TCP Server
虚拟仪器_labview_课件PPT_第十一章_通信编程
一点对多点通讯举例_TCP Client 1
一点对多点通讯举例_TCP Client 2
一点对多点通讯举例_TCP Server
- 2023-03-29 08:45:03下载
- 积分：1
-
USB-LABVIEW
The SC-2075 is a desktop signal conditioner that you can connect directly
to National Instruments E Series or 1200 Series devices. The SC-2075 has
the following features:
• Binding posts
– Three for ±15 V outputs
– Two for 0 to 5 V outputs
– Two for measuring analog signals or DC voltages
• BNC connectors
– Two for analog inputs
– Two for analog outputs
– One for triggering
• Spring terminals
– Eleven for analog inputs
– Seven for analog controls
– Seven for counter controls
– Two for TTL-level power and ground signals
– Eight for digital input/output (DIO) signals
- 2017-01-11 03:41:02下载
- 积分：1
-
labview-example-trigger
说明： 用labview编写的几种常用触发器程序及其仿真过程(Written by several common trigger labview program and its simulation)
- 2011-03-26 15:50:35下载
- 积分：1
-
yuhu8879
对LabVIEW进行二次开发，对振动信号进行HHT时频分析(The LabVIEW was developed two times, and the vibration signals were analyzed by HHT time frequency)
- 2020-12-11 11:19:18下载
- 积分：1
-
Virtual-control-of-excavator
挖掘机的虚拟控制,labview 2013，利用wrl格式3D模型可以更改为其他控制模型，可设置运行轨迹
(Virtual control excavator, labview 2013, use wrl format 3D model can be changed to other control models, you can set the running track)
- 2017-02-24 12:34:18下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
说明： 基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
LVBVIEW实现串口收发结果的波形图显示
LVBVIEW实现串口收发结果的波形图显示，界面美观实用,功能介绍：左边上方串口接收区，下方为串口字符发送区。右方为一个波形图表，在程序内部每次将串口发送过来的数据，以f%格式化，显示在波形图表上。
按钮介绍：从左至右依次，发送按钮；清除计数按钮；打开/关闭串口按钮；清除接收区数据；清除波形图表；保存波形；退出程序。
- 2022-01-26 02:25:25下载
- 积分：1
-
LVperl
说明： documents
- 2019-02-02 17:19:59下载
- 积分：1
-
autocorrelationfunction
基于LabVIEW的时域分析_自相关函数(autocorrelation function)
- 2020-11-14 09:29:44下载
- 积分：1
