-
chap11
说明： 本目录主要包括：文档和两个源代码。
其中一个源代码是识别程序的，另一个是一个矩阵类库的，书里面也使用过，所以一并附上。
因为已经保存了训练好的网络权值，所以第一次使用识别程序时，可以直接运行\\Release目录下的可执行文件，然后对图片目录中的测试图片进行读入、识别。
当然读者也可以自行用训练样本训练网络，不过要特别注意训练样本的选择，否则可能造成识别率很低。训练样本选择的原则是，尽可能的有代表性，在训练时间不至于太长的情况下，训练样本数目尽量多。
( This directory includes: documentation and two source code.
One of the source code is to identify the procedure, the other is a matrix class library, the book which is also used, so be attached.
Because it has saved the trained network weights, so the first use of identification procedures, you can directly run \ \ Release directory of the executable files, and then tested on the images directory to read pictures, identification.
Of course, readers are free to use the training samples to train the network, but pay special attention to training samples, otherwise it may cause very low recognition rate. Training sample selection principle is that as far as possible, representative, in the long training time Buzhi Yu s case, the number of training samples as much as possible.
)
- 2010-04-11 22:26:09下载
- 积分：1
-
遗传算法-电源规划
遗传算法-计算电源规划用，将低碳要素引入电源规划决策之中，在充分考虑传统电力系统安全、经济运行要求的前提下，建立了含碳捕集电厂的低碳电源规划模型(The ycsf genetic algorithm is used to calculate the power supply plan. The low-carbon elements are introduced into the power planning decision-making. Under the premise of fully considering the safety and economic operation requirements of the traditional power system, a low carbon power planning model of a carbon capture power plant is established.)
- 2018-02-19 15:55:24下载
- 积分：1
-
用 matlab 图像处理示例
Matlab 函数相关的偏微分方程的基础包括光流、 差距和分割的图像处理。这些函数进行作为我的博士论文，详细解释，模型是如何工作，如何对这些是离散并且有效地解决一部分。所以如果你想要了解这些模型是如何工作的我建议你看一下ww.jarnoralli.fi， 请点击左侧文件开始预览 ！预览只提供20%的代码片段，完整代码需下载后查看 加载中 侵权举报
- 2022-07-04 21:21:33下载
- 积分：1
-
oswaldfactor
Oswald efficiency estimation function
- 2012-12-31 08:47:38下载
- 积分：1
-
PID_Increase
增量式PID控制算法Matlab仿真程序
设一被控对象G（s）=50/(0.125s^2+7s),用增量式PID控制算法编写仿真程序（输入分别为单位阶跃、正弦信号，采样时间为1ms，控制器输出限幅：[-5,5],仿真曲线包括系统输出及误差曲线，并加上注释、图例）。(Incremental PID control algorithm Matlab simulation program to set up a controlled object G (s) = 50/(0.125s ^ 2+7s), with incremental PID control algorithm simulation program written (unit step input, respectively, sinusoidal signal sampling time is 1ms, the controller output limiter: [-5,5], including simulation system output and error curve curves, plus notes, legend).)
- 2014-01-09 20:54:10下载
- 积分：1
-
RBF用于电力负荷预测
次代码是用elman来预测电力负荷，用于短期电力负荷预测，属于自创，希望对广大学子有用
- 2023-03-20 15:45:04下载
- 积分：1
-
Wind-turbine-blades-design
本文利用MATLAB的遗传算法工具箱，对弦长和扭角沿风力机展向分布进行优化，得到设计工况下的最优叶片设计。目标函数是设计工况下基于动量叶素理论和Glauert等修正所得出的功率系数。在设计工况下得到的设计结果，其功率系数在一定的风速范围内都能保持一个较高的数值，同时其有效攻角分布大致都在所选翼型的升力与阻力系数的比值最大处，与理论相符合。其结果说明该优化实际的有效性。(In this paper, the use of MATLAB genetic algorithm toolbox, chord length and twist angle along the wind turbine development to distribution optimized to obtain the optimal design conditions blade design. The objective function is to design conditions based on the results of momentum blade element theory and Glauert correction power factor. Design results in the design conditions, the power factor within the range of wind speeds can maintain a higher value, the effective angle of attack distribution substantially in the the selected airfoil lift and drag coefficient ratio of maximum , theoretical analysis and show. The results indicate the validity of the actual optimization.)
- 2013-04-21 14:06:41下载
- 积分：1
-
gettransfer
用于测定传递函数的matlab程序,可以直接调用用于测定传递函数(the basic funtion to get a system transfunction，and it can be called easily)
- 2012-04-11 13:04:56下载
- 积分：1
-
_FuzzyPID
MATLAB算法 自己设计的 希望能帮助你 模糊PID(MATLAB algorithm design their own hope to help you fuzzy PID)
- 2015-04-20 21:48:44下载
- 积分：1
-
22
说明： 给仿真信号加入噪声信号，比如白噪声、有色噪声等等(Added to the simulated signal noise signal, such as white noise, colored noise, etc.)
- 2014-08-05 16:10:04下载
- 积分：1
