-
ACELLUT.c
ACE Algorithm implementation. (language = c with interface to matlab).
- 2009-12-29 18:39:56下载
- 积分：1
-
MonteCarlo
四进制通信系统的进行蒙特卡罗仿真程序，以正交信号为基础。当均值分别等于０，０.１，１.０，２．０时完成１００００个比特的仿真并求出误差概率。绘出理论误码率和蒙特拉罗仿真的差错率并进行比较这俩个结果，并绘出每个均值情况下判决器的１０００个接受信噪比抽样(Four-band communication system to carry out Monte-Carlo simulation procedures to orthogonal signal basis. When the mean, respectively, equivalent to 10,000 completed 0,0.1,1.0,2.0 bit error probability simulation and obtained. Mapping theory and蒙特拉罗BER simulation这俩error rate and compare results, and the mean circumstances of each mapped)
- 2008-07-08 14:03:41下载
- 积分：1
-
colorchange
说明： matlab图形图象绘制之颜色改变gui(matlab graphics color change gui)
- 2009-09-02 11:24:51下载
- 积分：1
-
houghyap
good program to correct angle in image ya
- 2011-11-27 05:35:56下载
- 积分：1
-
直接序列扩频水印的嵌入与提取
说明： 实现直接序列扩频水印的嵌入与提取。基于待嵌入消息生成二进制水印序列,生成扩频码，用消息序列调制生成水印序列。依次处理灰度图像的每一个载体图像像素，根据相应位置 水印序列完成嵌入修改。(Realize the embedding and extraction of direct sequence spread spectrum watermark. The binary watermark sequence is generated based on the message to be embedded, the spread spectrum code is generated, and the watermark sequence is generated by message sequence modulation. Each carrier image pixel of gray image is processed in turn, and the embedding modification is completed according to the corresponding position watermark sequence.)
- 2020-12-06 20:19:23下载
- 积分：1
-
信号与信息处理
信号与信息处理――阵列信号处理DOA估计的matlab算法，这是线性调频信号的稀疏分解的另一种算法源码-Signal and information processing- array signal processing matlab algorithm for DOA estimation, which is a linear FM signal another sparse decomposition algorithm source code
- 2022-02-22 00:58:46下载
- 积分：1
-
全面的有小波分析的盲信号处理程序
关于小波的matlab复合分析，基于人工神经网络的常用数字信号调制，是信号处理的基础，包括调制，解调，信噪比计算，DC-DC部分采用定功率单环控制，包括主成分分析、因子分析、贝叶斯分析。
- 2022-07-25 09:30:34下载
- 积分：1
-
p0310
在MATLAB环境下，P0309运用5种不同的梯度增强法进行图像锐化 P0310：图像的高通滤波和掩模处理(In the MATLAB environment, P0309 use of five kinds of different gradient enhanced image sharpening method P0310: Image of high-pass filtering and mask treatment)
- 2007-08-13 11:28:28下载
- 积分：1
-
Robot-arm-non-standard-LQR-Control
单级机械臂的位置控制，由于需要调整时间和最大输入力矩的要求，程序实现两种非标准的LQR控制(The single-stage manipulator position control, due to the need to adjust the time and the maximum input torque requirements of the program to achieve the two non-standard LQR control)
- 2012-08-20 11:13:19下载
- 积分：1
-
powertrain-mounting_Opti
发动机悬置系统解耦率、固有频率以及参数优化程序(Engine mounting system decoupling rate, the natural frequency and parameter optimization program)
- 2014-02-12 21:32:14下载
- 积分：1
