-
Routing
分布式异步路由算法中——距离向量算法的C语言仿真实现，非常好地模拟了网络中各节点的路由情况(Distributed asynchronous routing algorithm- distance vector algorithm C language simulation, very good simulation of the network, each node in the routing case)
- 2021-04-09 11:09:00下载
- 积分：1
-
stm8l寄存器例程
常见的单片机操作，IO，中断，定时器，低功耗模式等(io, interrupt, timer, low power mode and so on)
- 2019-05-24 23:00:01下载
- 积分：1
-
directshow.net
完整的 DirectShow 接口函数和示例代码。(Complete interface function and sample code of DirectX.)
- 2011-04-18 23:40:34下载
- 积分：1
-
双平面分块法相机标定
应用棋盘格标定板，c++语言，结合opencv库的双平面相机标定方法，根据双平面标定法求解相机的隐式参数，然后根据求得的隐式参数校正、恢复图像
- 2022-11-04 14:15:03下载
- 积分：1
-
lesson17_3 - 单个字符
说明： 接到单片机上后，输出到示波器可以看到一定频率的方波，通过按键可以调节波形的频率，同时在显示屏上也可以产生对应的周期和频率，外加信号发生器，可以得出对应的周期频率(After being connected to the single chip computer, the square wave of a certain frequency can be seen when it is output to the oscilloscope. The frequency of the waveform can be adjusted by keystrokes. At the same time, the corresponding period and frequency can be generated on the display screen, and the corresponding periodic frequency can be obtained by adding a signal generator.)
- 2020-06-17 20:20:07下载
- 积分：1
-
Asynchronous Mode to dial out from D/300SC
ASYOUT.C ---- Asynchronous Mode to dial out from D/300SC-E1 -ASYOUT.C---- Asynchronous Mode to dial out from D/300SC-E1
- 2022-07-05 02:53:22下载
- 积分：1
-
EX27_FIR
使用DSP320F2812在CCS3.3编译环境里编程有限冲激响应，并得到很好的应用(Use DSP320F2812 CCS3.3 compiled in environment programming limited impulse response, and get a good application
)
- 2012-04-16 09:13:21下载
- 积分：1
-
TFT7565
用LPC2200控制TFT，完成的程序，可以使用(LPC2200 controlled by TFT, the completion of the procedure, you can use)
- 2008-06-13 17:17:18下载
- 积分：1
-
FingerPrintVerify
说明： 这是一个用C++语言实现一个指纹识别程序，要求满足FVC国际竞赛标准，并在学校建立的指纹库上实测。程序里应用到的技术有：中值滤波、直方图均衡化、脊线方向提取、Gabor滤波、指纹细化、特征提取、特征点过滤、基于局部特征点的特征匹配(This is a C++ Language realization of a fingerprint identification procedure, the requirements FVC meet international competition standards, and established in the school library on the measured fingerprint. Program applied to the technology are as follows: median filter, histogram equalization, the direction of the ridge line extraction, Gabor filtering, fingerprint thinning, feature extraction, feature point filtering, based on local feature points of the feature matching)
- 2020-11-02 09:09:54下载
- 积分：1
-
modeling_a_city
该文档描述了如何使用sketchup制作3D模型，并上传到google的3D仓库。(This document describes how to create 3D models using sketchup and uploaded to google' s 3D warehouse.)
- 2011-06-02 02:05:40下载
- 积分：1
